All Triumph Parts

Triumph (all parts stocked)



Contact Us For Details



Contact Us For Details

BRAKE PAD INFORMATION
( B001 )

BRAKE PADS - We stock organic (Armstrong), Semi-sintered (Nissin NS - see picture left) and fully sintered (DP and Nissin ST - see picture left) brake pads. Organic pads are resin bonded, kind to the discs, generally quieter and fine for general road use. Sintered pads are made from metal particles put under pressure and heat, offer the best stopping power, but also cause the most rotor wear and can make the most noise. Virtually all original equipment pads are now sintered. They are also the least affected by adverse conditions and are the pad to choose for high speed and track days. Sintered pads can feel 'grabby' and may lack 'feel' at the lever. Semi-metallic pads fall right in the middle for durability and performance. A trade off between sintered and organic, they still stop well, cause less rotor wear with better lever feel than sintered metallic pads and normally make less noise.

Nissin brake pad compound chart shown left.



Contact Us For Details

Front Brake Master Cylinder Seal Kit 11 mm bore
( B004 )

Rebuild kit to fit Nissin 11mm bore front brake master cylinders,

Fits:  Adventurer, America, Bonneville 800/865, T100, SE, Legend TT, Scrambler, Speedmaster (single disc), Street Cup, Street Twin, Thruxton and Thunderbird 900.



£24.95
More info  

Front Brake Master Cylinder Seal kit 14mm
( B005 )

Rebuild kit to fit Nissin 14mm bore front brake master cylinders,

Fits: Daytona 600/650, Daytona T595, 955 Daytona, Rocket III, Classic, Roadster, Speed Four, Speed Triple T509, 955 Speed Triple, 1050 Speed Triple to VIN  461331,   750/900 Trident, Sprint 900 and Trophy 900 up to vin 9082, 955 Sprint ST, 955 Sprint RS, 1050 Sprint ST (up to vin 274425) some fuel injected models have  been retrospectively fitted with 5/8" bore master cylinders to reduce lever travel -check before ordering). Street Triple, Sprint 900 and Trophy 900 up to vin 9082, TT600, Tiger 800, Tiger XC, Tiger 900 (carburettor model)



£24.95
More info  

Front Brake Master Cylinder Seal Kit 5/8
( B006 )

Rebuild kit for Nissin 5/8" bore front brake master cylinders.

Fits 750/900 Speed Triple, 900/1200 Daytona, Sprint Sport, Sprint Executive, Trophy 900 (from vin 9083), Sprint 900 (from vin 9083), Sprint 1050 ST (from vin 274426)



£24.95
More info  

Front Brake Master Cylinder Seal Kit 1/2
( B007 )

Rebuild seal kit to fit Nissin 1/2" bore front brake master cylinders.

Fits Thunderbird Sport, Tiger 900i, Tiger 955, Speedmaster (twin disc)

 



£24.95
More info  

Rear Brake Master Cylinder Rebuild Kit
( B010 )

Rebuild kit for all Triumph (Nissin) rear brake master cylinders.

Fits America, Bonneville 800/865, T100, 600/650/675/750/900/955/1000/1200 Daytona, 750/900 Trident, 750/900/955/1050 Speed Triple, 900/1200 Trophy, Scrambler, Speed Four, Speemaster, Street Triple, Thunderbird 900, Legend, Adventurer, Thunderbird Sport, Sprint 900, Sprint Sport, Sprint Executive, Sprint ST 955/1050, Sprint GT, 955 Sprint RS, Street Triple, Tiger 800/900/955/1050, Tiger 800, Tiger XC, TT600



£27.50
More info  

Rear Brake Master Cylinder seal Kit 1/2
( B011 )

Most Triumph produced have14 mm bore rear master cylinder size and use seal kit B010, but a few have 1/2 " to change the hydraulic pedal/caliper ratio.  If your bike is listed below check the size (it's cast into the side of the master cylinder) before ordering either this 1/2 " or Product B010 the 14 mm kit.

Fits, Bobber, Rocket III, Classic, Roadster, Tiger 800, XC, XR



£27.50
More info  

Seal Kit Nissin 6 Piston Caliper (Cast)
( B050 )

Complete seal kit for Nissin 6 piston cast calipers our part numbers B791 and B792. These will also fit all 750 MV Agusta F4  and F4 1000S 6 piston front calipers used from 1999 to 2006. All the piston seals are genuine Nissin made in Japan. Seals are to fit piston size 22, 25 and 30 mm.



£27.95
More info  

Seal Kit Nissin 6 Piston Caliper (CNC Machined)
( B051 )

Complete seal kit for Nissin 6 piston CNC machined calipers. All the piston seals are genuine Nissin made in Japan. Seals are to fit piston size 25, 27 and 27 mm.



£27.95
More info  

4 piston front caliper seal kits for Nissin and Triumph calipers
( B056 )

Fits all Nissin and Triumph front 4 piston calipers on all (Apart from Brembo) Triumph sports and touring models. Kit contains 8 seals (4 outer dust seals and 4 hydraulic seals). To equilize brake pad wear, these calipers use 2 different piston sizes, 30mm (leading) and 34mm (trailing). Use silicone or rubber grease during assembly after cleaning out any corrosion from the dust seal groove. The joint seals on the 2 halves are now also included. The piston seals are genuine Nissin parts as used as original equipment by Triumph. Made in Japan.

 

 

600/650/675/750/900/955/1000/1200/2300



£22.95
More info  

Seal set 2 piston calipers
( B057 )

27mm caliper seals used on all 2 piston calipers fitted to the Triumph range. These are genuine Nissin seals. The kit contains seals to repair x 1 caliper (4 seals). When fitted correctly in a clean groove, there is a smooth action of the piston with no tying up on the dust seal. After cleaning out any corrosion in the the dust seal groove, always use silicone or rubber grease when fitting.  Made in Japan.

Fits front and rear on:

Bonneville, T100, America, Speedmaster, Scrambler, Street Cup, Street Scrambler, Thruxton,Thunderbird 900, Thunderbird Sport, Legend TT, Adventurer,Trident 750/900, Tiger 900, Tiger 955, Trident Sprint (up to VIN 9082), Trophy 900 (upto VIN 9082), Trophy 1200 (up to VIN 4901)

Fits front only on

Tiger 800, Bobber, T120,

Fits rear on

Daytona 750/900/1000/1200, Daytona T595, Daytona 955, Speed Triple 750/900, Speed Triple T509, Speed Triple 955, 1050, Speed Triple R, S, Sprint ST 955, Sprint ST 1050, Sprint RS (single sided swinging arm), Tiger Explorer, Tiger Sport, Trophy 1215, SE, Trophy 900/1200, Sprint 900, Sprint Executive, Sprint Sport

 

 



£14.95
More info  

Front brake reservoir container.
( B193 )

Genuine Nissin front brake reservoir plastic pot used many Triumph models. This inclues the link pipe which fits some but no all models.

Fits  TT600, Speed Four, 600/650/675/955 Daytona, T595, T509, Thruxton, SE, Bonneville (from vin 380777) , 955/1050 Speed Triple, Sprint 955 ST/RS, 1050 Sprint ST, Tiger 1050, Sprint 1050 GT.



£19.99
More info  

Angled inlet to master cylinder with seat/circlip kit
( B194 )

Angled inlet to front brake reservoir used on most sports models. The 'O' ring seal and circlip are the same components used in the inlet to Nissin rear brake master cylinders. Genuine Nissin component. Made in Japan.

Fits TT600, Speed Four, 600/650//955 Daytona, T595, T509, Thruxton, SE, Bonneville (from vin 380777) , 955 Speed Triple, 1050 Speed Triple (up to VIN 461331), Sprint 955 ST/RS, 1050 Sprint ST, Tiger 1050, Sprint 1050 GT



£17.95
More info  

Master cylinder piston outer boot (front)
( B225 )

Nissin front brake master cylinder outer boot. Fits all models with Nissin front brakes.

750/900 Trident, 600/650/750/900/955/1000/1200 Daytona, 750/900/955 Speed Triple, 900/955 Tiger, Thunderbird 900, Thunderbird Sport, Legend, Adventurer, 900/1200 Trophy



£4.95
More info  

2 piston Nissin caliper pin boots
( B274 )

Slider pin pair of boot/covers for the 2 piston Nissin calipers.

These fit the front calipers of the following: 750/900 Trident, 900 Sprint and Trophy (up to vin 9083), 1200 Trophy (up to vin 4902), Tiger 900, Tiger 900 (EFI), Tiger 955, Tiger 800, Tiger XC, Thunderbird 900, Legend, Thunderbird Sport, Adventurer

Fit the rear caliper of the following: 750/900 Trident, 900/1200 Trophy, 750/900 Speed Triple, 750/900/1000/1200 Daytona, Tiger 900 (carburettor model), 955 Daytona, 955 Speed Triple, T595, T509, 1050 Speed Triple, 1050 Tiger, Tiger 900 (EFI), Tiger 955,  Tiger 800, Tiger XC, Tiger Explorer, 955 Sprint ST, 1050 Sprint ST, Sprint GT, 955 Sprint RS (single sided swinging arm model), Bonneville 800/865, T100, Thruxton, SE, Scrambler, America, Speedmaster, Thunderbird 900, Thunderbird Sport, Legend, Adventurer



£8.95
More info  

Rear brake master cylinder push rod
( B279 )

Rear brake master cylinder rod with a choice of 52 mm, 45 mm or 38 mm of 8 mm x 1.25 pitch thread. This will fit many models and the thread can be cut for most models to shorten to the required length. 

Thunderbird 900, Legend, Adventurer, Thunderbird Sport, T595/955/600/650 Daytona, T509/955/1050 Speed Triple, 955/1050 Sprint ST, 955 Sprint RS, 955/1050 Tiger





£16.00
More info  

Brake bleed screw covers
( B286 )

x 3 rubber bleed screw covers.



£1.95
More info  

Rubber grease sachet
( B291 )

Use a light coating of rubber grease when replacing brake caliper seals. Sachet contents 5g.



£1.75
More info  

Brake paste
( B292 )

Brake paste, ideal for brake pad pin threads.



£1.95
More info  

Rear brake switch hydraulic type.
( B302 )

Replacement rear brake switch to fit all 3/4 cylinder carburettor models, Bonneville range, 955 Sprint RS and ST.

 

750/900 Trident, 750/900/1000/1200 Daytona, 900/1200 Trophy, 750/900 Speed Triple, Sprint 900, Sprint Sport, Sprint Executive, Tiger 900/955, Thunderbird 900, Thunderbird Sport, Legend, Adventurer, Sprint 955 ST and RS.



£13.95
More info  

Nissin Front Brake Master Cylinder 14 mm
( B387 )

Nissin Front Brake Master Cylinder 14 mm with remote reservoir pot. Can be fitted to many models with 14 mm original size.

Fits or can be adapted to: Daytona 600/650, Daytona T595, 955 Daytona, Rocket III, Classic, Roadster, Speed Four, Speed Triple T509, 955 Speed Triple, 1050 Speed Triple to VIN  461331,   750/900 Trident, Sprint 900 and Trophy 900 up to vin 9082, 955 Sprint ST, 955 Sprint RS, 1050 Sprint ST (up to vin 274425) some fuel injected models have  been retrospectively fitted with 5/8" bore master cylinders to reduce lever travel -check before ordering). Street Triple, Sprint 900 and Trophy 900 up to vin 9082, TT600, Tiger 800, Tiger XC,                                                            



£135.00
More info  

Uprated Nissin front brake master cylinder
( B389 )

Reduce brake lever travel when changing from the original 14mm bore to this 5/8" bore remote pot sports master cylinder.

Dark grey finish on master cylinder.



£135.00
More info  

Uprated Nissin front brake master cylinder (black)
( B399 )

Reduce brake lever travel when changing from the original 14mm bore to this 5/8" bore. Remote pot reservoir sports style master cylinder. 

Black finish on master cylinder

 

 



£145.00
More info  

Nissin hydraulic clutch master cylinder (black)
( B400 )

Nissin clutch master cylinder. Latest sports style with remote reservoir pot. Fits all 3 and 4 cylinder carburettor models. Same 14 mm bore size as original part. Black finish on master cylinder.

Fits 750/900 Trident, 750/900 Speed Triple, 750/900/1000/1200 Daytona, 900/1200 Trophy, Tiger 900 (carburettor), Sprint Sport, Sprint 900, Sprint Executive, Thunderbird 900, Thunderbird Sport, Adventurer and Legend.



£136.00
More info  

Nissin hydraulic clutch master cylinder (black)
( B400 )

Nissin clutch master cylinder. Latest sports style with remote reservoir pot. Fits all 3 and 4 cylinder carburettor models. Same 14 mm bore size as original part. Black finish on master cylinder.

Fits 750/900 Trident, 750/900 Speed Triple, 750/900/1000/1200 Daytona, 900/1200 Trophy, Tiger 900 (carburettor), Sprint Sport, Sprint 900, Sprint Executive, Thunderbird 900, Thunderbird Sport, Adventurer and Legend.



£136.00
More info  

Nissin brake pad locator
( B418 )

The 2 piston Nissin caliper used on the rear of many models and  retro front calipers. The caliper moves on slider pins when the brake is applied. The outer brake pad has a hook located in this brake pad locator nut which is screwed onto one of the slider pins. Manufactured from stainless steel. (See slider pins listed below, also in stainless steel).

These fit the front calipers of the following: 750/900 Trident, 900 Sprint and Trophy 900 (up to vin 9083), 1200 Trophy (up to vin 4902),

Fit the rear caliper of the following: 750/900 Trident, 900/1200 Trophy, 750/900 Speed Triple, 750/900/1000/1200 Daytona, Tiger 900 (carburettor model), 955 Daytona, 955 Speed Triple, T595, T509, 1050 Speed Triple, 1050 Tiger, Tiger Explorer, 955 Sprint ST, 1050 Sprint ST, 955 Sprint RS (single sided swinging arm model),

Made in UK



£11.95
More info  

2 piston caliper slider bracket pins (pair)
( B419 )

Stainless steel replacemet pins for the 2 piston (on one side) calipers used  on the rear of most models and front of  very early Trophy, Sprint, and Trident models. The used bracket assembly is shown for reference only to help illustrate pin location.

These fit the front calipers of the following: 750/900 Trident, Tiger 900 (carburettor models), 900 Sprint and Trophy 900 (up to vin 9083), 1200 Trophy (up to vin 4902),

Fits the rear caliper of the following: 750/900 Trident, 900/1200 Trophy, 750/900 Speed Triple, 750/900/1000/1200 Daytona, Tiger 900 (carburettor model), 955 Daytona, 955 Speed Triple, T595, T509, 1050 Speed Triple, 1050 Tiger, Tiger Explorer, 955 Sprint ST, 1050 Sprint ST, Sprint GT, 955 Sprint RS (single sided swinging arm model), Bonneville 800/865, T100, Thruxton, SE, Scrambler, America, Speedmaster

 



£19.95
More info  

Caliper bracket
( B421 )

Threaded rear caliper bracket (less caliper slider pins).

Fits, Trident 750/900, Tiger 900 (carburettor), 900/1200 Trophy, 750/900/1000/1200 Daytona, Sprint 900, Sprint Sport, Sprint Executive



£19.00
More info  

Brake Banjo Bolt Stainless Steel (Single)
( B429 )

Single banjo width Earl's stainless steel brake banjo bolt for most application where x 1 hose is fitted.

M10 x 1.25 pitch thread.



£4.95
More info  

Brake Banjo Bolt Stainless Steel (Double)
( B430 )

Double width banjo stainless steel bolt for x 2 hose connection. Examples are front brake splitter on 3 and 4 cylinder carburettor models.

M10 x 1.25 pitch thread.



£5.49
More info  

Brake Banjo Annealed Copper Washers 10 mm
( B432 )

Original style copper washer 10 mm bore, 15.70 outer diameter and 1.20 mm thick. Pack size 10 pieces. Made in USA.



£3.95
More info  

Disc bolt
( B433 )

Plated steel disc bolt M8 x 1.25 mm pitch. Thread length 30 mm including 10 mm shoulder. The plating isn’t as good as original parts, but the steel is excellent and less prone to chewing up with the hex key.

Fits front and rear on 750/900 Trident, 900/1200 Trophy, 750/900/1000/595/955/1200 Daytona, 750/900/T509/955/ Speed Triple, 900 Sprint, Sprint Sport, Sprint Executive, Sprint RS,

Fits front only on T595, 955 Daytona, T509, 955 Speed Triple, 955/1050 Sprint ST, Sprint RS (single sided swinging arm).



£1.95
More info  

27mm caliper piston and seals (Stainless Steel)
( B436 )

Stainless steel caliper piston 27 mm diameter and 31 mm long with seals for x 1 caliper (x 2 pistons and x 4 seals). These are not genuine Nissin parts.

Fits front and rear calipers on Thunderbird 900, Legend, Thunderbird Sport, Adventurer, 750/900 Trident, 900/955 Tiger, Bonneville, T100, Thruxton, America, Speedmaster, SE, Scrambler, Trophy 900 and Sprint 900 up to vin 9083, Trophy 1200 up to vin 4902

Fits rear caliper only on 750/900/1000/1200 Daytona, 955 Daytona (single sided swinging arm model), 750/900/955/1050 Speed Triple, 900 Sprint Sprint Sport, Sprint Executive, 955/1050 Sprint ST, Sprint RS (single sided swinging arm), Sprint GT, Tiger 1050, Tiger 1050 SE, Trophy 900 and Sprint 900 from vin 9084, Trophy 1200 from vin 4903

Fits front caliper Tiger 800, Tiger XC, Street Triple 675,



£44.95
More info  

Caliper piston 34mm (4 piston caliper)
( B437 )

Larger 34mm diameter trailing piston used in Nissin and ''Triumph'' 4 piston type calipers. Fitted to the front of all Daytona models (up to the use of radial calipers), 900/955 Sprint, Trophy and 900/955 Speed Triples etc.  The pistons are 22.5 mm long. These are genuine Nissin pistons made in Japan.

To fit front calipers on 750/900/1000/1200 Daytona, 750/900 Speed Triple, 900/1200 Trophy, 900 Sprint, Sprint Sport, Sprint Executive, 955/1050 Sprint ST, RS, T509, 955 Speed Triple, T595, 955 Daytona, TT600, Speed 4, 600/650 Daytona, Rocket 3,

 



£19.00
More info  

Caliper piston 30mm (4 piston calipers)
( B438 )

Nissin 4 piston calipers have 2 different size pistons to even out pad wear. This is the smaller 30mm (leading) diameter piston used on 4 piston Nissin calipers. This piston will fit all 4 piston Nissin and ''Triumph'' calipers up to the latest radial style. Piston depth 22.5 mm. This is a genuine Nissin part. Made in Japan.



£15.00
More info  

Rear Caliper Piston and Seal kit 38 mm (pattern)
( B448 )

Pattern caliper piston and seals to fit rear calipers on all sports twin sided swinging arm models.

Fits TT600, Speed Four, Daytona 600, Daytona 650, Daytona 675, Street Triple, Daytona 955 (twin sided swinging arm model), Tiger 800, Tiger XC,



£24.00
More info  

Brake Bleed Screw
( B472 )

Brake caliper bleed screw/nipple to fit Nissin calipers used on Triumph models. Genuine Nissin part.



£2.95
More info  

Pad pin screw covers for Nissin calipers.
( B604 )

x 2 screw covers to fit most Nissin calipers used on retro and adventure Triumph models. These are 10mm  x 1.00 mm pitch.

Thunderbird 900, Legend, Thunderbird Sport, Adventurer, Tiger 800, Tiger 800XT, Tiger 955, Tiger 900 (injection), Bonneville range (fron calipert), Speedmaster, America, Thruxton



£3.50
More info  

Brake Pad Pins. Thunderbird, Tiger, Bonneville
( B605 )

Brake pin and screw cover for Thunderbird, 955 Tiger and Bonneville range.  Approximately 59mm long. This pad pin is used as one per caliper at the end of the pads and is accessed by first removing the slotted screw cover. Sold as a pair.

Pins fit front and rear calipers on Tiger 900 (injection), 955 Tiger, Thunderbird 900, Thunderbird Sport, Adventurer and Legend.

Pins fit the front caliper only on Bonneville 800/865, T100, Thruxton, America, Speedmaster, Scrambler, Tiger 800, Tiger 800 XC and 675 Street Triple



£9.99
More info  

Brake caliper pins 64 mm
( B606 )

64mm long pad pins used on the rear of many Triumph models. These are also used on the front of all Tridents and early Trophy/Sprint models with twin piston (reaction type) calipers. This style of caliper uses 2 pins  to retain the pads. These are sold as a pair. The pad pins are genuine Nissin parts made in Japan.



£8.99
More info  

Pad Pins. Front 4 Piston Type Caliper.
( B607 )

Pad pins to fit all 4 piston ''Nissin'' and ''Triumph'' calipers. These are approximately 53 mm long.  x1 pin used per caliper to retain the pads, these do not project through the inside of the caliper and finish flush with the caliper body. 955 Daytona, 955 Speed Triple and 600/650 models used a longer pin with a split pin on the inside, the 53 mm long pins are fine as replacements. Sold as a pair. Genuine Nissin parts made in Japan.



£8.99
More info  

Brake pad pin rear Nissin Tiger 800, TT600, Daytona 955
( B609 )

Rear brake caliper pad pin and screw cover fits Nissin rear calipers on:

Daytona 600/650, 675 Daytona to VIN 564947, Daytona 995 (twin sided swinging arm model only), Speed Four, Street Triple and Street Triple R up to VIN 560476, Tiger 800, XC, XCA, XCx, XR, XRT, XRx, TT600



£7.99
More info  

Caliper right/rear
( B642 )

Thunderbird, Adventurer, Legend, and Thunderbird Sport rear brake caliper. Also the same as the front right on the Thunderbird Sport. The 900 EFI/955 Tiger models are fitted with a cosmetically slightly different Nissin caliper but this is dimensionally the same as the original caliper and can also be fitted on the right to these Tigers. It will also fit the rear of  all spoked wheel 1999-2004 injected 900/955 Tigers. A different caliper is used on the rear only of the 2005 955 with cast alloy wheels. All calipers are black and supplied complete, less only pads and fixing bracket.



£169.00
More info  

Caliper Right and Rear
( B643 )

Complete replacement caliper as ID 642 but with slider bracket and pads.



£223.00
More info  

Rear Brake Caliper 955/1050 Sprint RS and ST
( B645 )

Rear caliper to fit 1050 Sprint ST, 955 Sprint RS (single sided swinging arm model only) and 955 Sprint ST models. Complete caliper ready to fit less slider bracket and pads. Fits ABS and non ABS.

Fits Tiger 900 (carburettor) left side front,  Sprint ST 955 rear, Sprint ST 1050 rear and Sprint RS (single sided swinging arm model) rear.



£179.00
More info  

Front Brake Caliper Nissin 4 piston type (left) Triumph or Nissin
( B650 )

Nissin original equipment 4 piston front brake caliper. These are fitted to many Triumph models, either with the 'Nissin' or 'Triumph' logo.  Bolt fixing centre distance 90mm. These will fit all Trophy, carburettor Daytona/Speed Triple, all 900 Sprint, 955 Sprint ST/RS and many more, but do not fit the 955 Daytona/Speed Triple which have 83mm fixing centres. This is the left side caliper

750/900/1000/1200 Daytona, 750/900 Speed Triple, 900/1200 Trophy,  900 Sprint Sport,  Sprint Executive, 955 Sprint  ST, 955 Sprint RS,



£169.00
More info  

Front Brake Caliper Nissin 4 piston (right).
( B651 )

Nissin original equipment 4 piston front brake caliper. These are fitted to many Triumph models, either with the 'Nissin' or 'Triumph' logo.  Bolt fixing centre distance 90mm. These will fit all Trophy, carburettor Daytona/Speed Triple, all 900 Sprint, 955 Sprint ST/RS and many more, but do not fit the 955 Daytona/Speed Triple which have 83mm fixing centres. This is the right side caliper

750/900/1000/1200 Daytona, 750/900 Speed Triple, 900/1200 Trophy,  900 Sprint Sport,  Sprint Executive, 955 Sprint  ST, 955 Sprint RS,

 

 



£169.00
More info  

Nissin Radial Caliper Seals 1050/675
( B685 )

Nissin radial caliper seals to fit 1050 Speed Triple, 1050 Tiger and 675 Daytona. The kit  is for one caliper, consists of 4 piston seals and 4 dust seals.The joint seals betweeen the 2 caliper halves are now included with the kit. This kit does not fit the Brembo radial caliper. The piston seals are genuine Nissin and made in Japan. The joint seals are not Nissin.

 



£22.95
More info  

Disc Bolt 10 mm shoulder 30 mm long
( B810 )

Stainless steel disc bolt M8 x 1.25 mm pitch. Thread length 30 mm including 10 mm shoulder.

Fits front and rear on:

Bobber, Bonneville T120, Daytona 750/900/1000/1200, Daytona 600/650, Daytona 675, Daytona 955 (twin sided swinging arm), Rocket III, Speed Four, 750/900 Speed Triple, Sprint 900, Sprint Executive, Sprint Sport, Sprint RS (twin sided swinging arm), Street Cup, Street Scrambler, Street Triple 675, Street Triple R, S RS, Thruxton R (liquid cooled), Tiger 800, Tiger 1050, 750/900 Trident, 900/1200 Trophy, TT600

Fits front only on:

Daytona T595, Daytona 955 (single sided swinging arm), Speed Triple 955/1050, Sprint RS (Single sided swinging arm), Sprint ST 955/1050,



£5.49
More info  

Disc Bolt 1.5 mm shoulder 18 mm long
( B811 )

Stainless steel disc bolt M8 x 1.25 mm pitch. Thread length 18 mm including 1.5 mm shoulder.

Fits front and rear on:

Adventurer, America, Bonneville, T100, Legend TT, Scrambler,  Speedmaster, Thruxton, Thunderbird 900, Thunderbird Sport, Tiger 900 (carburettor and EFI), Tiger 955

Fits rear only on:

T595, 955 Daytona, T509, 955 Speed Triple, 955/1050 Sprint ST, Sprint RS (single sided swinging arm).

 

 



£5.49
More info  

Brake pad Armstrong Bonneville, Thunderbird 900, Tiger 800/955
( B902 )

Armstrong semi metallic brake pads.

Fits the front of the following: Bonneville, T100, Scrambler, Speedmaster, America, Thunderbird 900, Legend, Adventurer, Thunderbird Sport, Tiger 800, Tiger XC, Tiger 900 (injection), Tiger 955, 675 Street Triple (not R model)

Fits the rear of the following: Thunderbird 900, Legend, Adventurer, Thunderbird Sport, Tiger 900 (injection), Tiger 955 (up to vin 198874)

Supplied as 2 pads for x 1 caliper



£12.95
More info  

Brake pad Nissin Bonneville, Thunderbird 900, Tiger 800/955
( B903 )

Nissin NS semi metallic brake pads.

Fits the front of the following: Bonneville, T100, Scrambler, Speedmaster, America, Thunderbird 900, Legend, Adventurer, Thunderbird Sport, Tiger 800, Tiger XC, Tiger 900 (injection), Tiger 955, 675 Street Triple (not R model)

Fits the rear of the following: Thunderbird 900, Legend, Adventurer, Thunderbird Sport, Tiger 900 (injection), Tiger 955 (up to vin 198874)

Supplied as 2 pads for x 1 caliper



£32.95
More info  

Brake pad Nissin front/rear Trident, Trophy, Sprint
( B906 )

Nissin NS semi metallic front brake pads.

Supplied as 2 pads for x 1 caliper.

Fit rear of the following: 750/900 Trident, 750/900 Speed Triple, 750/900/1000/1200 Daytona, 900/1200 Trophy, Sprint 900, Sprint Sport, Sprint Executive, Tiger 900 (carburettor models), Sprint 955 RS (twin sided swinging arm models),Tiger 955 cast wheels (from vin 198875) and Tiger 1050

Fit the front right side of the following: 750/900 Trident, 900 Trident Sprint and Trophy 900 (up to vin 9082), Trophy 1200 (up to vin 4901)



£32.95
More info  

Brake pad Armstrong front/rear Trident, Trophy, Sprint
( B907 )

Armstrong brake pads. Supplied as 2 pads for x 1 caliper.

Fit rear of the following: 750/900 Trident, 750/900 Speed Triple, 750/900/1000/1200 Daytona, 900/1200 Trophy, Sprint 900, Sprint Sport, Sprint Executive, Tiger 900 (carburettor models), Sprint 955 RS (twin sided swinging arm models), Tiger Explorer, Tiger 955 cast alloy wheel model (from vin 198875), Tiger 1050

Fit the front right side of the following: Tiger 900 (carburettor), 750/900 Trident, 900 Trident Sprint and Trophy 900 (up to vin 9082), Trophy 1200 (up to vin 4901

 



£12.95
More info  

Brake pad Nissin Bonneville (rear), 955, 1050
( B910 )

Nissin NS semi metallic brake pads. Supplied as 2 pads for x 1 caliper.

Fits the rear of the following: Tiger Explorer, Bonneville, T100, Scrambler, America, Speedmaster. All single sided models T595 Daytona, 955 Daytona, T509, 955 Speed Triple, 1050 Speed Triple, 955 Sprint ST, 1050 Sprint ST, Sprint 955 RS (single sided swinging arm models), Trophy 1215 & SE, Tiger Sport

Fits the front left side of the following: 750/900 Trident, 900 Trident Sprint and Trophy 900 up to vin 9082, Trophy 1200 up to vin 4901



£32.95
More info  

Brake pad Armstrong Bonneville (rear), 955, 1050, 900 left front
( B911 )

Armstrong brake pads. Supplied as 2 pads for x 1 caliper.

Fits the rear of the following: Tiger Explorer, Bonneville, T100, Scrambler, America, Speedmaster. All single sided models T595 Daytona, 955 Daytona, T509, 955 Speed Triple, 1050 Speed Triple, 955 Sprint ST, 1050 Sprint ST, Sprint 955 RS (single sided swinging arm models), Trophy 1215 & SE, Tiger Sport

Fits the front left side of the following: 750/900 Trident, 900 Trident Sprint and Trophy 900 up to vin 9082, Trophy 1200 up to vin 4901



£12.95
More info  

Brake pad Nissin rear Rocket 3, Thunderbird 1600/1700
( B912 )

Nissin NS semi metallic rear pads.

Fits the rear: Rocket III, Thunderbird 1600, Thunderbird 1700.



£32.95
More info  

Brake pad rear Nissin 675 Daytona, Street Triple, Tiger 800, TT600
( B914 )

Nissin NS semi metallic rear brake pad.

Fits the rear of the following: TT600, Speed 4, Daytona 600, Daytona 650, Daytona 675, Street Triple, Street Triple R, Daytona 675 R, Daytona 955 (twin sided swinging arm), Tiger 800, Tiger XC,



£32.95
More info  

Rear Brake Pads 675, TT600, Tiger 800, Street Triple
( B915 )

Nissin NS semi metallic rear brake pad.

Fits the rear of the following: TT600, Speed 4, Daytona 600, Daytona 650, Daytona 675, Street Triple, Street Triple R, Daytona 675 R, Daytona 955 (twin sided swinging arm), Tiger 800, Tiger XC,



£12.95
More info  

Brake pad Nissin Daytona, Speed Triple, Sprint
( B919 )

Nissin NS semi metallic front pads fit all 4 piston Triumph/Nissin 4 piston axial (not radial) calipers. These were used by Triumph on as original equipment on all 3/4 cylinder carburettor models and will also fit later models with the same calipers..

Fits the front of the following: 750/900/1000/1200 Daytona, Trophy 1200 from vin 4902, Trophy 900 and Sprint 900 from vin 9083, Sprint Sport, Sprint Executive, 750/900 Speed Triple, 955 Daytona, T595, T509, 955 Speed Triple, Tiger Explorer, Rocket III, TT600, Speed 4, Daytona 600/650, 955 Sprint ST, 955 Sprint RS, 1050 Sprint ST, Sprint 1050 GT, Supplied as 2 pads for x 1 caliper



£32.95
More info  

Brake Pads to fit Brembo calipers on Daytona 675R and 1050 Speed Triple R
( B923 )

Nissin ST sintered high performance brake pads to fit Brembo front brake calipers used on Daytona 675R and 1050 Speed Triple R models. Supplied as 2 pads for x 1 caliper.



£42.00
More info  

DP (Dunlopad) Daytona Super III, 1200 Daytona Alcon 6 Piston Caliper Pads
( B925 )

Daytona Super III original equipment DP416 (Dunlopad) sintered brake pads used only on the Alcon 6 piston calipers. Also fits Alcon 6 piston caliper on 1200 limited edition model. Supplied as x 2 pads to fit x 1 caliper. Made in UK



£24.50
More info  

Dynavolt YB14LA2 gel sealed battery
( BA019 )

Sealed Dynavolt gel battery, sealed upgrade for YB14LA2

Fits: 750/900 Trident, 900/1200 Trophy, Legend, Thunderbird, Thunderbird Sport ,Adventurer, 750/900/1000/1200 Daytona, 750/900 Speed Triple, Sprint 900, Sprint Sport, Sprint Executive and Tiger 900

Also fits: T595/955 Daytona up to vin 71698, T509/955 Speed Triple up to vin 79696 



£53.95
More info  

YTX14BS Motobatt 16.5 Amp hour Upgrade
( BA114 )

16.5 AH (Amp hour) rated battery from Motobatt to replace YTX14BS. This Motobatt has x 4 terminals to easily add accessoriesis such as a smart battery charger lead. We have sold these to many other project and special builders. Battery size is 150 mm long x 88 mm wide x 144 mm high.

240 CCA (cold cranking amps) 

Fits Trophy 900/1200 from VIN 71699,  Tiger 900 (injection), T595 from VIN 71699, Daytona 955, T509 from VIN 71699,  Speed Triple 955, Sprint RS 955 Sprint ST 955, Tiger 955



£59.95
More info  

Battery Motobatt YTX12-BS and YTX14BS
( BA265 )

 High power 14 amp/hour but YTX-12BS size battery. Replaces YTX14BS and YTX12BS.



£54.00
More info  

Battery Motobatt YB14LA2
( BA266 )

Sealed Motobatt replacement for the YB14LA2 battery. Battery has 2 pairs of terminals to make connecting smart charger leads easier. Motobatt claim 20% more cranking power - 210 CCA (cold cranking amps). Now rated at 16.5 AH.

Fits: 750/900 Trident, 900/1200 Trophy, Legend, Thunderbird, Thunderbird Sport ,Adventurer, 750/900/1000/1200 Daytona, 750/900 Speed Triple, Sprint 900, Sprint Sport, Sprint Executive and Tiger 900

Also fits: T595/955 Daytona up to vin 71698, T509/955 Speed Triple up to vin 79696 



£67.95
More info  

Front Wheel Bearings and Seals 675
( BE068 )

Koyo front wheel bearings x 2 and dust seals x 2.

Fits: Bonneville Bobber, T120, 675 Daytona, 675 Daytona R, Street Scrambler, Street Triple, Street Triple R, Thruxton (liquid cooled), Thruxton R (liquid cooled)



£22.95
More info  

Front Wheel Bearings 600/675/955
( BE070 )

x 2 Koyo front wheel bearings to fit

TT600, Speed Four, Daytona 600/650, Daytona 675, Street Triple, 955 Speed Triple from VIN 141872, 955 Daytona from VIN 132513,



£17.00
More info  

Front Wheel Bearings Trident, daytona, Trophy, 955 ST and RS
( BE072 )

x 2 Koyo bearings to fit

Front wheel on 750/900 Trident, 750/900/1000/1200 Daytona, 900/1200 Trophy, Sprint 900, Sprint Sport, Sprint Executive, Thunderbird 900, Legend, Adventurer, Thunderbird Sport, 750/900 Speed Triple, America (spoked wheel), America (cast wheel) 1050 Sprint ST, 1050 Sprint GT, 1050 Speed Triple (From VIN 210445 to VIN 461331, Tiger 1050 (From VIN 287504 to VIN 570058),

Rear wheel  on America (cast wheel)

 

 



£17.00
More info  

Front Wheel Bearings Tiger 900/955, Bonneville
( BE074 )

x 2 Koyo wheel bearings to fit

Fits front wheel: Tiger 900 (carburettor), Tiger 900 (injection), Tiger 955 all models, Bonneville, T100, Thruxton, Scrambler

Fits rear wheel: Bonneville 800/865, T100, Scrambler, Thruxton 900

 



£17.00
More info  

Rear Wheel Bearings Trident, Trophy, Daytona
( BE076 )

x 2 Koyo REAR wheel bearings to fit

Tiger 900 (carburettor), Tiger 900 (injection), 750/900 Trident, 900/1200 Trophy, Sprint 900, Sprint Sport, 750/900/1000/1200 Daytona, 750/900 Speed Triple, Thunderbird 900, Legend, Adventurer, Thunderbird Sport, 955 Tiger (wire/spoked wheel model)



£17.00
More info  

Sprocket Carrier Bearing
( BE077 )

Sprocket carrier (cush drive) bearing to fit:
750/900 Trident, 750/900 Speed Triple, 750/900/1000/1200 Daytona, 900/1200 Trophy, Tiger 900 (injection and carburettor), Sprint 900, Sprint Sport, Sprint Executiive, Tiger 955 (wire wheel version) up to VIN198874, Thunderbird 900, Adventurer, Legend, Thunderbird Sport, America and  Speedmaster.



£9.95
More info  

Wheel Bearing (Koyo) and dust seals Tiger 800, Tiger 955, TT600
( BE078 )

Japanese Koyo wheel bearings (sold as a pair with dust seals for x 1 wheel).

Fits FRONT WHEEL: Tiger 800 and Tiger XC.

Fits REAR WHEEL: Daytona, 675, Tiger 800, Tiger XC, Tiger 1050, Tiger 955 (cast wheel model), Speed Four, Street Triple, TT600, Daytona 600/650 and Sprint RS (twin sided swinging arm).



£23.95
More info  

Sprocket Carrier Koyo Bearing and Seal Tiger 800, 955
( BE082 )

Japanese Koyo sprocket carrier (cush drive) bearing and seal to fit:

Tiger 800, Tiger 800 XC

Tiger 955 (cast wheel)

Bonneville, T100, America, Speedmaster, Thruxton, Scrambler

TT600, Speed Four, Daytona 600/650

955 Sprint RS (twin sided swinging arm)

955 Daytona (twin sided swinging arm)

675 Daytona, Street Triple

 



£9.95
More info  

Sprocket Carrier Bearing Single sided Swinging Arm Models
( BE600 )

Japanese twin ball 55X35X20 NTN bearing and dust seal to fit sprocket carrier (cush drive) on single sided swinging arm models. NTN has been used as the original equipment bearing.

Fits Daytona T595, Speed Triple T509, Daytona 955 (single sided), Sprint ST 955/1050, Sprint GT, Sprint RS 955 (single sided), Speed Triple 955/1050 and 1050 Tiger and Tiger Sport.



£29.95
More info  

Rear Wheel Bearings/Seals Single Sided Swinging Arm Models
( BE601 )

Rear wheel bearings (rear axle eccentric adjuster bearings), double ball bearing and needle roller with x 2 separate seals.

Fits T595, T509, 955 Speed Triple, 955 Daytona, 955 Sprint ST,single sided swinging arm Sprint RS, 1050 Sprint ST up to VIN 388246 and 1050 Speed Triple up to vin 346969.



£69.00
More info  

Rear Wheel Bearings/Seals Single Sided Swinging Arm Models
( BE602 )

Rear wheel bearings (rear axle eccentric adjuster bearings), sealed needle roller and double ball bearing.

To fit 1050 Sprint ST from VIN 388247, 1050 Sprint GT and 1050 Speed Triple from vin 346969.



£85.00
More info  

Valve Shims 25 mm 2.05 - 2.25
( BE699 )

Valve shim 25 mm diameter. Sizes from 2.05 to 2.25.

Fits: Adventurer, America, Bonneville, T100 & SE, Daytona 750, 900, 1000, 1200, Daytona T595, Daytona 955 up to VIN 132512, Legend, Rocket III, Classic, Roadster & Touring, Scrambler, Speedmaster, 750 & 900 Speed Triple, Speed Triple T509, 955 Speed Triple up to VIN 141871, Sprint 900, Sprint Sport, Sprint Executive, Sprint RS & ST 955 up to VIN 139276, Thruxton, Thunderbird 900, Thunderbird Sport, Tiger 900 (carburettor), Tiger 900 (injection), Tiger 955i, 750 & 900 Trident, Trophy 900 & 1200





£7.95
More info  

Valve Shims 25 mm 2.30 - 3.20
( BE700 )

Valve shim 25 mm diameter. Sizes from 2.30 to 3.20

Fits: Adventurer, America, Bonneville, T100 & SE, Daytona 750, 900, 1000, 1200, Daytona T595, Daytona 955 up to VIN 132512, Legend, Rocket III, Classic, Roadster & Touring, Scrambler, Speedmaster, 750 & 900 Speed Triple, Speed Triple T509, 955 Speed Triple up to VIN 141871, Sprint 900, Sprint Sport, Sprint Executive, Sprint RS & ST 955 up to VIN 139276, Thruxton, Thunderbird 900, Thunderbird Sport, Tiger 900 (carburettor), Tiger 900 (injection), Tiger 955i, 750 & 900 Trident, Trophy 900 & 1200

 





£3.95
More info  

Valve Shims 9.5 mm 1.70 - 2.95
( BE702 )

9.5 mm valve shim.

Fits: Daytona 955 from VIN 132513, 955 Speed Triple from VIN 141872, 1050 Speed Triple, 1050 Speed Triple R, 955 ST and RS from VIN 139277,  1050 Sprint ST, 1050 Sprint GT, Tiger 1050, Tiger Explorer and XC, Trophy 1215





£3.95
More info  

Valve Shims 7.5 mm 1.80 - 2.95
( BE704 )

7.5 mm valve shim.

Fits: Daytona 600/650, Daytona 675, Daytona 675 R, Speed Four, TT600, Street Triple, Street Triple R, Tiger 800, Tiger 800 XC, Tiger XR.

 





£3.95
More info  

Lever Clamp/Mirror Support
( C195 )

Replacement or new clamp for models with no mirror fixing. Used as original on clutch and front brake lever on 955/1050 Speed Triple, Speed Four, Thruxton and 955 Tiger. Ideal to hold mirrors when converting from Daytona to speed triple.  Made in Japan.



£9.95
More info  

Clutch lever span adjustable
( C346 )

Direct replacement for 675 Daytona, Street Triple 675, 1050 Speed Triple, Sprint ST 1050, Sprint GT, 1050 Tiger, Tiger Sport, Scrambler and Thruxton. Or upgrade on 600/650 Daytona, Tiger 800, Tiger XC, 955 Daytona and 955 Speed Triple both from vin. 186150>, Street Twin, Bonneville T120, Bonneville T120 Black, Thruxton (Liquid cooled), Thruxton R (Liquid cooled), 

Only fits Tiger 800 range up to VIN 674842 and Tiger Sport up to VIN 750469.



£14.95
More info  

Clutch lever 600/650/675/955 Daytona, Street Triple and 955 Speed Triple.
( C347 )

Replacement lever for Daytona 600/650, 675 Daytona and Street Triple 675. Also fits Speed Four after vin 201642, 955 Daytona models from vin 186150. Late model single sided swinging arm 955 Sprint RS from vin 186151.



£11.50
More info  

Clutch lever T595/955 Daytona, 955 ST/RS and 955 Speed Triple.
( C348 )

Clutch lever fits all TT600, Speed Four as well as 955 Sprint RS/ST, T595/955 Daytona and 955 Speed Triple models up to VIN 186150.



£10.00
More info  

Clutch lever adjustable black
( C349 )

Replacement lever for many early models 900/1200 Trophy, 750/900/1000/1200 Daytona, 750/900 Speed Triple and 750/900 Trident.



£14.95
More info  

Front brake lever adjustable black
( C350 )

Fits most early carburettor models, including 900/1200 Trophy, 750/900/1000/1200 Daytona, 750/900 Speed Triple and 750/900 Trident.



£14.95
More info  

Clutch lever
( C351 )

Replacement clutch lever for 900 Thunderbird, Legend and Adventurer.



£12.00
More info  

Front brake lever
( C352 )

Replacement front brake lever for 900 Thunderbird, Legend and Adventurer.



£12.00
More info  

Adjustable levers alloy (Pair)
( C353 )

Upgrade for 900 Thunderbird, Legend and Adventurer.



£29.75
More info  

Adjustable Front brake lever 600/650/955 Daytona and 955 Speed Triple.
( C354 )

Correct shape replacement front brake lever to fit TT600, Speed Four, 600/650 Daytona, Street Triple 675, Scrambler, Thruxton, SE and Bonneville from vin 380777, T509 Speed Triple, T595/955 Daytona, 955 Speed Triple, 1050 Speed Triple up to vin 333179 and 1050 Tiger.

Will also fit to upgrade to adjustable on Bonneville, T100, America and Speedmaster.



£16.95
More info  

Front brake Tiger Explorer, Tiger 800
( C356 )

Front brake lever as fitted to Street Twin, Bonneville T120, Bonneville T120 Black, Thruxton (Liquid cooled), Trophy 1215, Trophy 1215 SE, Tiger 800, Tiger XC, XCA, XRT, Tiger 1050, Tiger Sport and Tiger Explorer. Can be fitted to most of the Triumph non radial front brakes if desired. Alloy finish.



£14.95
More info  

Clutch Lever Tiger 900 EFI and Tiger 955
( C361 )

Clutch Lever Tiger 900 EFI and all Tiger 955



£12.95
More info  

Clutch lever Tiger 900
( C363 )

Clutch lever to fit all Tiger 900 carburettor models. Also used on early versions of the Trident 750/900, Trophy 900/1200 and Sprint 900.



£12.95
More info  

Front Brake Lever Tiger 900
( C364 )

Forged front brake lever to fit all Tiger 955, 900 carburettor and EFI models. Also used on early versions of the Trident 750/900, Trophy 900/1200 and Sprint 900



£22.95
More info  

Clutch lever Thunderbird 1600/1700
( C365 )

Replacement clutch lever to fit Thunderbird 1600 and 1700, Storm. Commander and LT.



£12.00
More info  

Front brake lever Thunderbird 1600/1700
( C366 )

Replacement front brake lever to Thunderbird 1600 and 1700.



£12.00
More info  

Front Brake Lever Daytona 675/ 1050 Speed Triple
( C449 )

Replacement front brake lever to fit Nissin radial brake caliper model Daytona 675 and 1050 Speed Triple.



£14.99
More info  

Adjustable clutch lever T595/ 955 Daytona and 955 Sprint RS/ST
( C450 )

CNC machined billet span adjustable clutch lever fits all TT600, Speed Four as well as 955 Sprint RS/ST, T595/955 Daytona and 955 Speed Triple models up to VIN 186150.



£29.95
More info  

Front Brake Lever Thunderbird Sport
( C465 )

Front brake lever to fit Thunderbird Sport. Polished lever blade and black pivot.



£15.00
More info  

Clutch lever Thunderbird Sport
( C466 )

Clutch lever for Thunderbird Sport. Polished lever blade and black pivot.



£15.00
More info  

Clutch Lever Explorer and Trophy 1215
( C468 )

Adjustable clutch lever to fit Tiger Explorer, Trophy 1215 and Trophy 1215 SE



£17.50
More info  

Choke cable Speed Triple 900, Daytona 900/1200
( CC695 )

Choke cable to fit Speed Triple 750/900, Daytona 750/900/1000/1200. Inner cable length 84 cm.



£16.95
More info  

Choke Cable Tiger 900, Thunderbird 900, Legend
( CC700 )

Choke cable to fit Legend TT, Thunderbird 900, Trophy 900/1200 (twin headlight model) and Tiger 900. Inner length 100 cm.



£16.95
More info  

Choke Cable Sprint 900, Trident, Trophy
( CC702 )

Choke cable to fit Sprint 900, Sprint Sport, Sprint Executive, Thunderbird Sport, Trident 750/900 (up to VIN 29155), Trophy 900/1200. Inner length 92 cm.



£16.95
More info  

Choke Cable Adventurer
( CC703 )

Choke cable to fit Adventurer. Inner cable length 107 cm.



£16.95
More info  

Throttle Cable Adventurer Mikuni carburettors
( CC704 )

Throttle Cable for Adventurer fitted with Mikuni carburettors. Original bikes up to VIN 71698 used Mikuni carburettors. Inner length 118 cm.



£19.95
More info  

Throttle Cable Keihin Carburettors Trident, Sprint 900
( CC706 )

Throttle Cable Sprint 900, Sprint Sport, Sprint Executive, Trident 750/900, Trophy 900/1200. Inner length 102 cm. For Keihin carburettors.



£19.95
More info  

Throttle Cable Mikuni Carburettors Trident, Sprint 900
( CC707 )

Throttle Cable Sprint 900, Sprint Sport, Sprint Executive, Trident 750/900, Trophy 900/1200. Inner length 102 cm. For Mikuni carburettors.



£19.95
More info  

Speedo Cable T595 and 955 Daytona
( CC716 )

Speedo cable to fit: Daytona T595 and 955 Daytona up to VIN 132512

Inner cable length 78 cm

Take care not to over tighten the 5 mm screw holding the cable into the drive unit



£14.95
More info  

Speedo cable 86cm
( CC718 )

Speedo cable 86cm long.

Take care not to over tighten the 5 mm screw holding the cable into the drive unit



£14.95
More info  

Speedo cable Trident, Bonneville
( CC720 )

Speedo cable 95cm (37 1/2") outer length to fit  750/900 Trident, 900/1200 Trophy (single headlamp model), carburettor Daytona 750/900/1000/1200 models, Bonneville from VIN 38077, SE, Scrambler and 750/900 Speed Triple. Replaces Triumph T2040481.

Take care not to over tighten the 5 mm screw holding the cable into the drive unit



£15.00
More info  

Speedo Cable Trophy and Tiger
( CC722 )

Speedo cable 101cm (39 3/4") outer length to fit twin headlamp Trophy, Sprint 900, 750/900 Speed Triple, Sprint Sport, Sprint Executive, Tiger, Adventurer, Thunderbird 900, Thunderbird Sport and Legend TT

Take care not to over tighten the 5 mm screw holding the cable into the drive unit



£15.00
More info  

Speedo Cable Speedmaster
( CC724 )

Speedo cable 108cm (42 5/8")  fits the Speedmaster (all models carburettor and efi) and is ideal for modified/special applications.

Take care not to over tighten the 5 mm screw holding the cable into the drive unit



£15.00
More info  

Speedo cable outer length 126cm
( CC725 )

Longest speedo cable we stock at 126cm. Ideal for modified bikes where extra length may be required.

Take care not to over tighten the 5 mm screw holding the cable into the drive unit



£14.95
More info  

Clutch Cable T509 and 955 Speed Triple.
( CC726 )

Clutch cable to fit T509, 955 Speed Triple 1997-2001 (up to VIN 141871) and T595/955 Daytona models converted to Speed Triple style.



£15.00
More info  

Throttle cable Thunderbird Sport, Legend, Tiger 900 (Carb.) Trophy 95>
( CC727 )

Throttle cable to fit

Trophy 900/1200 from VIN 29156 (twin headlight models)

Thunderbird Sport

Tiger 900 (carburettor models)

Legend TT

Cable details: 110 cm inner cable. 103 cm outer.

This is a copy of Triumph cable T2043512 and can be fitted to Adventurer models with Keihin carburettors, but care with routing is required.

 



£14.95
More info  

Clutch Cable 955 Sprint ST
( CC728 )

European produced replacement clutch cable for 955 Sprint ST models. 98.5 cm outer.  106.5 cm inner.

Fits up all 955 ST up to VIN 186151



£14.95
More info  

Clutch Cable 1050 Sprint ST
( CC729 )

Clutch Cable 1050 Sprint ST to fit all export models and UK with lower handlebars. Inner cable length 112 cm. Outer length 103 cm.



£14.95
More info  

Clutch Cable Speed Triple 1050
( CC730 )

Clutch cable to fit 1050 Speed Triple up to VIN 461331



£14.95
More info  

Clutch Cable T595 and 955 Daytona
( CC731 )

Clutch cable to fit Daytona T595 and all 955 Daytona models up to VIN 132512. Inner cable length 112 cm. Outer length 103 cm.



£14.95
More info  

Throttle Cable Daytona T595, Speed Triple 955
( CC732 )

Throttle cable to fit:

Daytona T595

Daytona 955 up to VIN 132512

Speed Triple T509

Speed Triple 955 up to VIN 141871



£19.95
More info  

Clutch Cable Daytona 600 and 650
( CC734 )

Clutch cable to fit Daytona 600 and Daytona 650. Inner cable length 98 cm. Outer length 88 cm.



£14.95
More info  

Clutch cable TT600 and Speed Four.
( CC735 )

Clutch cable to fit Speed Four and TT600.  Outer length 94 cm.



£14.95
More info  

Throttle cable Speed Four and TT600
( CC736 )

Throttle cable to fit Speed Four and TT600. Inner cable length 106 cm  Outer length 97 cm.



£14.95
More info  

Throttle cable Tiger 900 EFI and all Tiger 955
( CC749 )

Throttle cable to fit Tiger 900 EFI (from VIN 71699) and all Tiger 955 models.

Inner cable length 139 cm. Outer 128 cm.



£19.95
More info  

Throttle cable Speed Triple 900 Daytona 900/1200
( CC750 )

Throttle cable to fit 750/900 Speed Triple, 750/900/1000/1200 Daytona and Trophy 900/1200 up to vin 4900.

Cable details: 94 cm inner cable. 84 cm outer.



£19.95
More info  

Clutch Cable Tiger 955
( CC752 )

Clutch cable to fit Tiger 955 and Tiger 900 (injection). Outer 1105 mm. Inner 1185 mm.



£14.95
More info  

Clutch Cable Sprint RS 955
( CC753 )

Clutch cable to fit all Sprint RS 955 models.



£14.95
More info  

Clutch Cable 955/1050 Alternative 101 cm Outer Length
( CC754 )

Alternative cable for handlebar changes with metal bend at handlebar end

Total length of inner cable 101 cm. Outer length 93 cm.



£14.95
More info  

Clutch cable Daytona 675
( CC765 )

Replacement clutch cable to fit Daytona 675 up to VIN 564947. Inner length 119cm. Outer length 107 cm  



£14.95
More info  

Clutch cable 800 Tiger
( CC768 )

Clutch cable to fit all Tiger 800 models. Inner length 113 cm.Outer length 101 cm.

Fits:Tiger 800, 800XCA, 800XCx, 800XR, 800XRT and 800XRx.

 



£19.95
More info  

Clutch Cable Bonneville America
( CC770 )

Replacement clutch cable to fit all Bonneville America models - carburettor and EFI.

Inner length 127.5 cm, outer length 115.5 cm



£14.95
More info  

Clutch cable Bonneville, T100, Speedmaster
( CC771 )

Replacement clutch cable to fit all Bonneville 800/865, T100 and Speedmaster models - carburettor and EFI.

Inner length 119.5 cm, outer length 107.5 cm



£18.95
More info  

Clutch Cable Speed Triple 955 01>
( CC774 )

Replacement clutch cable to fit 955 Speed Triple from VIN 141872. Outer length 99 cm. Inner cable length 107 cm.



£15.00
More info  

Twin throttle Cable 955 Daytona and 955 Speed Triple
( CC775 )

Twin throttles cables fitted to 955 Daytona fron VIN 132513 and 955 Speed Triple from VIN 141871



£19.95
More info  

Twin Throttle Cables 955 Sprint ST and RS
( CC776 )

Twin throttle cables to fit 955 Sprint ST and 955 Sprint RS  from VIN 139277



£19.95
More info  

Throttle Cable 955 Sprint ST up to VIN 139276
( CC777 )

Throttle cable to fit 955 Sprint ST up to VIN 139276.  Inner length 139.5 cm.



£19.95
More info  

Throttle Cable 955 Sprint RS up to VIN 139276
( CC778 )

Throttle cable to fit 955 Sprint RS up to VIN 139276. Inner length 141.5 cm.



£19.95
More info  

Fan Switch Trident, Trophy, Daytona 900/1200
( CL330 )

Cooling fan switch and sealing washer. Early fan switch fits on left side of radiator. Switches on at 96 C and switchws off when temperature is down to 88 C.

Fits 750/900 Trident, 900/1200 Trophy,  750/900/1000/1200 Daytona, 750/900 Speed Triple, Sprint 900, Sprint Sport, Sprint Executive and Tiger 900 (carburettor).



£19.95
More info  

Fan Switch Thunderbird 900
( CL339 )

Fan switch and seal to fit Thunderbird 900, Legend, Adventurer and Thunderbird Sport. Switches on when temperature reaches 96 C.



£24.95
More info  

Expansion Tank Elbow
( CL344 )

Black plastic elbow to fit expansion tanks. Sealing problems on the radiator to expansions tanks can allow water expansion but no siphon back with loss of coolant in the radiator.



£1.39
More info  

Expansion tank pipe joiner
( CL345 )

Had to cut/shorten rubber pipe from radiator cap to expansion tank ? This joiner allows for cutting and joining.



£1.49
More info  

Clutch master cylinder seal kit
( CL393 )

Seal kit for hydraulic clutch model master cylinder/control lever. 14 mm bore size.

Fits: 750/900/1000/1200 Daytona, Legend, 750/900 Trident, 750/900 Speed Triple, 900/1200 Trophy, 900 (carburettor) Tiger, 900 Sprint, Sprint Sport, Sprint Executive, Thunderbird 900, Adventurer, Thunderbird Sport



£23.95
More info  

Clutch Slave Cylinder Seal Kit
( CL442 )

Replacement seal kit for clutch slave cylinder, fits all 3 and 4 cylinder hydraulic clutch models.

750/900 Trident, 900/1200 Trophy, 750/900/1000/1200 Daytona, 750/900 Speed Triple, 900 Sprint, Sprint Sport, Sprint Executive, 900 Tiger (carburettor model), Thunderbird, Thunderbird Sport, Legend and Adventurer. Also fits Trophy 1215, SE, Tiger Explorer 1200/1215, XC, Xcx, XRT, Xrx



£23.00
More info  

Water pump seals
( CL497 )

Seal set for when the water pump is disturbed. x 3 seals seals include the red cover seal, O-ring seal into engine and O-ring on outlet metal pipe. The internal shaft seals are not available.

Fis 750/900 Trident, 750/900/1000/1200 Daytona, 900/1200 Trophy, 900 Tiger, 750/900 Speed Triple, Sprint Sport, Sprint Executive, Thunderbird 900, Thunderbird Sport, Legend and Adventurer.



£4.95
More info  

Water Pump Joint Seal
( CL499 )

Replacement red joint seal for when water pump is disturbed. O-ring where pump enters the engine and copper sealing washer under joint screw are also included.

Fits T595, T509, 955 Daytona, 955 Sprint ST, 955 Sprint RS, Tiger 900, Tiger 955, 955 Speed Triple



£3.95
More info  

Clutch Master Cylinder Seal Kit 1215 Trophy and Explorer
( CL670 )

Repair kit for clutch master cylinder 12.7 mm bore. Fits Trophy 1215, SE, Tiger Explorer 1200/1215, XC, Xcx, XRT, Xrx



£27.95
More info  

Clutch lever switch
( CL672 )

Clutch lever switch. Genuine Nissin part.

Fits: 750/900/1000/1200 Daytona, Legend, 750/900 Trident, 750/900 Speed Triple, 900/1200 Trophy, 900 (carburettor) Tiger, 900 Sprint, Sprint Sport, Sprint Executive, Thunderbird 900, Adventurer, Thunderbird Sport



£11.95
More info  

Clutch lever switch
( CL672 )

Clutch lever switch. Genuine Nissin part.

Fits: 750/900/1000/1200 Daytona, Legend, 750/900 Trident, 750/900 Speed Triple, 900/1200 Trophy, 900 (carburettor) Tiger, 900 Sprint, Sprint Sport, Sprint Executive, Thunderbird 900, Adventurer, Thunderbird Sport



£11.95
More info  

Clutch plate set T300 Trophy, Trident
( CL929 )

Clutch friction 9 plate set to fit all carburettor 3 and 4 cylinder models with cover gasket.

750/900 Trident, 750/900/100/1200 Daytona, 750/900 Speed Triple, 900/1200 Trophy, 900 (carburettor) Tiger, 900 Sprint, Sprint Sport, Sprint Executive, Thunderbird 900, Legend, Adventurer, Thunderbird Sport

 



£59.00
More info  

Clutch Spring Set
( CL930 )

EBC Clutch Spring set.

Fits 750/900 Trident, 750/900/1000/1200 Daytona, 750/900 Speed Triple, 900/1200 Trophy, 900 (carburettor) Tiger, 900 Sprint, Sprint Sport, Sprint Executive, Thunderbird 900, Legend, Adventurer, Thunderbird Sport



£10.95
More info  

Clutch plate set. 600 models.
( CL931 )

Friction plate set to fit TT600, 600 Daytona and Speed Four models. Manufactured by Ferodo in Italy



£59.00
More info  

Clutch plate set. 955 models (early engine)
( CL932 )

Clutch friction plate set (9 peices) to fit Daytona T595, T509, 955 Daytona up to VIN 132512, Speed Triple up to VIN141871, 900 Tiger (EFI), 955 Sprint ST and 955 Sprint RS up to VIN 139277.



£59.00
More info  

Clutch plate set. 955 models (later engine) and 1050
( CL933 )

Clutch friction plate set (10 peices) to fit Daytona 955 Daytona from VIN 132513, 955 Speed Triple from VIN141872, and 955 Sprint ST and 955 Sprint RS from VIN 139278. Also fits 1050 Speed Triple up to VIN 461331.



£69.00
More info  

Clutch Spring Set 955 and 1050
( CL935 )

EBC 10% uprated clutch spring set to fit all 955 and 1050 models.



£12.95
More info  

Clutch plate set Bonneville 800
( CL940 )

Clutch friction plate 7 piece set to fit 800 Bonneville models.



£59.00
More info  

Chain Rubbing Strip/Chain Slider Trident, Trophy, Daytona 900/1200
( CS119 )

Replacement swinging arm chain protector/slider. Replaces Triumph part  2056920-T0301.

Fits:Daytona 750/900/1000/1200, Super III, Speed Triple 900, Sprint 900, Sprint Executive, Sprint Sport, Trident 750/900, Trophy 900/1200

 



£14.95
More info  

Chain Rubbing Strip/Chain Slider 600, 955 RS and 955 Tiger (late)
( CS120 )

Chain rubbing strip to fit:

TT600, Speed Four

Sprint RS 955 (twin sided swinging arm models)

Tiger 955  From VIN 198875  (Cast alloy wheel models)

 

 



£14.95
More info  

Gearbox Sprockets 600/650 range.
( CS140 )

Gearbox sprockets available in 13, 14 or 15 teeth to fit all 600 and 650 models.





£15.00
More info  

Gearbox sprockets 900/1200/955/1050 (530)
( CS141 )

Gearbox sprockets available in 17, 18 or 19 teeth for all carburettor 3/4 cylinder models, all 955 and all 1050 models. Smaller than standand gives improved acceleration at the expense of fuel consumption and on some models increased chain guide wear. Larger than standard engine sprockets lose out slightly on acceleration but have a more relaxed feel in top gear.  Please state size when ordering. (530 chain size).





£15.00
More info  

Gearbox sprockets Bonneville range (525)
( CS142 )

Gearbox sprockets available in 17, 18 or 19T to fit all the Bonneville range. Please state size when ordering. (525 chain size)





£15.00
More info  

Rear sprockets (530)
( CS143 )

Rear sprockets in 40, 42, 43, 44, 45, 46, 47, 48 or 49 teeth to fit all carburettor 3 and 4 cylinder models as well as all wire wheel 955 Tiger models. Please state size when ordering. (530 chain size).





£25.00
More info  

DID Chain and Sprocket Kit (530)
( CS145 )

530 VX gold heavy duty X-ring DID chain with sprockets, tab washer and sprocket cover gasket if required. Please state model when ordering and if in doubt just let us know what sprocket sizes you would like. (530 chain size). Front/rear/chain length details given are for standard factory sizes. Other size choice no problem.  





£125.00
More info  

DID X-ring 525 chain and sprocket kit. Bonneville range/600/650/675
( CS151 )

DID VM2 X-ring gold chain and sprocket kit. Available for all Bonneville models, TT600, Speed Four, Daytona 675 and 675 Street Triple. Please state model when ordering. (525 chain size). Front/rear/chain length details given are for standard factory sizes. Other size choice no problem.  



£119.00
More info  

DID X-ring gold chain 525
( CS154 )

Original equipment DID VX/VM2 X-ring gold 525 chain. Fits, TT600, Speed Four, Daytoina 600/650, 675 Daytona, 675 Street Triple, 800 Tiger and Tiger XC.





£85.00
More info  

DID X-ring gold chain 530
( CS155 )

Original equipment DID VX  X-ring gold chain 530 size (5/8 x 3/8). Fits all 750, 900 (3/4 cylinder),1000, 955, 1200 and 1050 models.





£89.00
More info  

Tab Washer 675, 600 and 650 models
( CS173 )

Gearbox sprocket tab washer to fit: TT600, Speed Four, Daytona 600, Daytona 650, Daytona 675, Daytona 675R, Street Triple, Street Triple R, Tiger 800 and Tiger 800XC. 



£3.95
More info  

Lock Nut Flanged Sprocket Carrier
( CS174 )

12 mm x 1.25 flanged lock nut to hold rear sprocket on to carrier. Price for x 1 nut

Fits, Adventurer, 750/9001000/1200 Daytona, Legend TT, Speed Triple 750/900, Sprint 900, Sprint Sport, Sprint Executive, Thunderbird 900, Thunderbird Sport, Trophy 900/1200, Tiger 900, Tiger 955.



£1.00
More info  

Tab Washer Gearbox Sprocket 2, 3 and 4 cylinder carburettor models, 955, 1050.
( CS176 )

Gearbox sprocket tab (locking) washer to fit all of the Bonneville range (carburettor and EFI), 955, 1050 and 3/4 cylinder carburettor models.

 

Fits 750/900 Trident, 900/1200 Trophy, 750/900/1000/1200 Daytona, Super III, 900 Tiger, 750/900 Speed Triple, 900 Sprint, Sprint Sport, Sprint Executive, Thunderbird 900, Thunderbird Sport, Legend, Adventurer, T595, 955 Daytona, T509, 955 Speed Triple, 955 Sprint ST, 955 Sprint RS, 955 Tiger, 1050 Tiger, Tiger Sport, 1050 Sprint ST, 1050 Sprint GT, 1050 Speed Triple, Bonneville 800/865, T100, Scrambler, America, Speedmaster, Thruxton and SE.

Tab Washer Gearbox Sprocket 3 and 4 cylinder carburettor models, 955, 1050.



£3.25
More info  

Rear Sprocket. Bonneville and 600/650 (525)
( CS661 )

Rear sprockets available in 41, 42, 43, 44, 45 teeth to fit most of the Bonneville range and all 600/650 models. Please state size when ordering . (525 chain size).

Fits Bonneville 800/865, T100, Thruxton, Scrambler, TT600, Speed Four, Daytona 600 and Daytona 650





£25.00
More info  

Rear Sprocket Single Sided Swinging Arm Models (530)
( CS663 )

Rear sprockets available in 42, 43, 44 or 45 teeth to fit all single sided swinging arm models. Please state size when ordering.  (530 chain size).

T595. T509, 955 Daytona, 955/1050 Speed Triple, 955/1050 Sprint ST, 955 Sprint RS (single sided swinging arm)





£25.00
More info  

Rear Sprocket 955 Twin Sided Swinging Arm Models (530)
( CS664 )

Rear sprockets in 40, 42, 43, 44, 45 or 46  teeth to fit 955 Tiger (not 955 Tiger with wire wheels-see ID143) and 1050 Tiger twin sided swinging arm models. Please state size when ordering. (530 chain size).

955 Daytona (twin sided swinging arm), 955 Sprint RS, 955 Tiger (cast alloy wheel model 2005/2006), 1050 Tiger





£25.00
More info  

Rear Sprocket America and Speedmaster (530)
( CS665 )

42T Rear sprocket to fit the America and Speedmaster models. (525 chain size).



£25.00
More info  

675 and 800 Gearbox Sprocket (525)
( CS945 )

Gearbox sprocket to fit Daytona 675, Street Triple, Tiger 800 and Tiger XC. Sizes available  14, 15 , 16 and 17 teeth.   (525 chain size)





£15.00
More info  

Rear Sprocket 675 and 800 (525)
( CS946 )

Rear sprocket to fit Tiger 800, Tiger XC, Daytona 675 and Street Triple available  in 47, 49 and  50 teeth. (525 chain size)





£25.00
More info  

Chain Rivet Tool
( CS950 )

Replica DID chain rivet tool. This will push the rivet link together and neatly rivet the ends over. To separate an old chain or shorten a chain, grind the rivet ends one side of the link to be removed until the side plate is hit. Go slightly below the surface to be sure the rivetting is well ground away, then knock apart with a punch and hammer.



£39.95
More info  

Trident 750/900 Front Disc
( D003 )

Replacement front discs to fit Trident 750 and 900. 296 mm diameter. Price for x 1 disc. This will fit left and right.

Fits 750/900 Trident, Trophy 900 and Sprint 900 up to vin 9083, Trophy 1200 up to vin 4902



£79.00
More info  

Front Disc 900 Tiger (carburettor)
( D006 )

Front disc to fit all carburettor Tiger 900. 1993-98. Quantity x 1 disc. This fits all Tiger 900 up to VIN 71698. Made in UK.



£79.00
More info  

Front Disc 310 mm Bonneville, Tiger 955, Thunderbird Sport
( D008 )

310 mm front disc. Fits Bonneville 800/865, T100, Thruxton.Scrambler, America, Speedmaster, Thunderbird Sport and Tiger 955. Quantity x 1 disc.



£89.00
More info  

Front Disc Tiger 955 and Tiger 1050
( D009 )

Front disc to fit Tiger 955 from VIN 198875 (cast wheel) and Tiger 1050.



£84.95
More info  

Front Discs Daytona 675, Street Triple, TT600 and Daytona 600/650
( D010 )

x 2 replacement front discs to fit TT600, Speed Four, Daytona 600, Daytona 650, Daytona 675 and Street Triple.

 



£199.00
More info  

Front Disc 320 mm Thunderbird, Legend and Adventurer
( D011 )

320 mm front disc to fit Thunderbird, Legend and Adventurer.



£79.00
More info  

Front disc black, 310mm floating. Daytona 900/1200, Speed Triple 900 and Trophy 900/1200
( D012 )

Original style replacement 'floating' 310mm front disc used on 900/1200 Daytona, 750/900 Speed Triple, Sprint 900, Sprint Sport, Sprint Executive and 900/1200 Trophy models with 4 piston Nissin/Triumph calipers. Black centre exactly styled on the first original equipment discs used on Daytona 900/1200 and Speed Triple 900 models. Left or right. Made in UK.

 

 

 

 

 

 



£124.00
More info  

320mm front disc 6 hole fitting for T595, 955 Sprint ST/RS (pair)
( D013 )

320mm floating disc, 6 bolt fitting for Daytona T595, Speed Triple 955 and Daytona 955 up to vin 1232513, all 955 Sprint ST, all 955 Sprint RS and T509 Speed Triple. 6 mm offset. Later models have a 5 hole fitting disc. Sold as a pair. Made in UK.



£235.00
More info  

320mm front disc 5 hole fitting for Daytona 955 (pair)
( D014 )

x 2 front discs 320 mm with 6mm offset.

To fit: Daytona 955 from vin 132513,  Speed Triple 955 from vin 141872

Please check the off set before ordering (inside face against the wheel to the inside face of the disc rotor).

Made in UK.



£235.00
More info  

320mm front disc 5 hole fitting 1050 Sprint ST
( D015 )

Front disc 320 mm outer diameter,  with 10mm offset. Sold as a pair.

To fit: Sprint ST 1050 (up to VIN 440388).

Please check the off set before ordering (inside face against the wheel to the inside face of the disc rotor).



£199.00
More info  

Rear Disc 220 mm T595, T509, 955 Daytona, 955 Speed Triple
( D016 )

220 mm rear disc to fit TT600, Speed Four, Daytona 600, Daytona 650, T595, T509, 955 Daytona, 955 Speed Triple, 1050 speed Triple, 675 Daytona and Street Triple.



£69.00
More info  

Rear Disc 255 mm Sprint ST, Sprint RS, Bonneville, Thruxton
( D017 )

255 mm rear disc to fit Bonneville 800/865, T100, Thruxton, Scrambler, Sprint ST 955, Sprint ST 1050, Sprint RS and Tiger 800. Available for ABS and non ABS.





£79.00
More info  

Rear disc Tiger 900
( D019 )

Rear disc to fit all carburettor Tiger models. 255 mm. This fits all Tiger 900 up to VIN 71698



£79.00
More info  

Front Disc Bonneville SE and from VIN 380777 (Cast Alloy Wheel)
( D020 )

Front disc to fit cast aluminum alloy wheel models. Made in UK.

Fits: Bonneville from VIN 38077, Bonneville SE and Speedmaster (EFI) left side disc.



£79.00
More info  

Rear Disc tiger 955 and Tiger 1050
( D022 )

Rear disc to fit Tiger 955 from VIN 198875 (cast wheel) and Tiger 1050 (twin sided swinging arm). Made in UK.



£79.00
More info  

285 mm Rear Disc for 4 Bolt Cast Wheel in Thunderbird 900 Range
( D025 )

4 bolt fitting 285 mm rear disc to fit Thunderbird Range where a 3 spoke cast wheel from 600/650/955 models is used.

Thunderbird 900, Thunderbird sport, Legend and Adventurer.



£79.00
More info  

Rear Disc 255 mm Trident, Trophy, Sprint 900
( D039 )

255 mm rear disc to fit 750/900 Trident, Trophy 900/1200, Daytona 750/900/1000/1200, 750/90 Speed Triple, Trident Sprint, Sprint 900, Sprint Sport and Sprint Executive.



£79.00
More info  

Front Discs Floating Upgrade Trident Trophy
( D179 )

Floating discs to replace solid original 296 mm discs used on Trident, Trophy and Sprint 900. Manufactured by EBC and sold as a pair. Made in UK.

Fits 750/900 Trident, Trophy 900 and Sprint 900 up to vin 9083, Trophy 1200 up to vin 4902



£289.00
More info  

Front brake disc 1050 Tiger and Speed Triple
( D263 )

Front disc to fit 1050 Tiger and 1050 Speed Triple up to vin number 350905. 5 hole disc with 12.5 mm off set. Price for x 1 disc. Available with gold or black centre.

Please check the off set before ordering (inside face against the wheel to the inside face of the disc rotor).





£119.00
More info  

320MM Front Disc 6 Hole T595, 955 SPRINT ST/RS (PAIR)
( D266 )

320mm front disc 6 hole fitting for T595, 955 Sprint ST/RS (pair)

320mm floating disc, 6 bolt fitting
Fits: Daytona T595, Speed Triple 955 and Daytona 955 up to vin 1232513, all 955 Sprint ST, all 955 Sprint RS and T509 Speed Triple. 6 mm offset. Later models have a 5 hole fitting disc.


£199.00
More info  

Front Disc Thunderbird 1600/1700
( D267 )

Replacement front disc to fit Thunderbird 1600/1700 models. 310 mm outer diameter, 78 mm inner and 100 mm fixing hole PCD. 5 mm thick flat (no offset).

Also fits as floating disc conversion: Bonneville from VIN 380777, SE and Speedmaster (EFI).



£99.00
More info  

Rear Disc America, Speedmaster, Thunderbird 900, Tiger 955
( D269 )

285 mm rear disc to fit Thunderbird 900, Legend, Adventurer, Thunderbird Sport, Tiger 900 EFI, Tiger 955 (wire spoked wheels), Speedmaster and America.



£79.00
More info  

Regulator 955
( EG399 )

Regulator fits inside alternator on all 955 models with alternator behind engine. Daytona T595, Daytona 955 up to vin 132512, 955 Sprint ST and RS up to vin 139275. Also fits Trophy 1200 made after vin 55346 and injected Tiger 900.



£39.95
More info  

Regulator unit to fit separate Denso generator. Trident, Trophy, Thunderbird 900
( EG400 )

Replacement regulator to fit Denso generator used on all Trident, Trophy, 750/900/1000/1200  Daytona, 750/900 Speed Triple, Tiger 900, Sprint 900, Thunderbird 900, Thunderbird Sport, Legend, Adventurer, Sprint ST 955 (up to vin 139276), Sprint Sport, Sprint RS (up to vin 139276), T509 Speed Triple, 955 Speed Triple (up to vin 141871), T595 and 955 Daytona (up to vin 132512)

Made in Argentina



£69.95
More info  

1050 Speed Triple, Tiger, Sprint 1050 ST, Daytona 955
( EG499 )

114mm diameter replacement generator stator kit for 955 Daytona from VIN 132513, 1050 Speed Triple, 1050 Tiger and 1050 Sprint ST.

PLEASE MEASURE GENERATOR DIAMETER BEFORE ORDERING AS VIN NUMBERS ARE JUST A GUIDE

 

 



£119.95
More info  

Generator stator 955 Tiger, 955 ST/RS, Speed Triple
( EG500 )

104mm generator stator to fit 955 Tiger, 955 Sprint ST (from vin 139277), 955 Sprint RS (from vin 139277) and 955 Speed Triple (from vin 141871 to 183487)

PLEASE MEASURE GENERATOR DIAMETER BEFORE ORDERING AS VIN NUMBERS ARE JUST A GUIDE

 



£124.95
More info  

Regulator Rectifier Electrex unit 600/650/955 /1050
( EG684 )

Hi-power series regulator rectifier with MOSFET technolgy. UK based company Electrex have taken a fresh look at this problem part. This is the very latest Electrex unit with direct connection to the battery terminals bypassing problems associated by going through the wiring loom. Supply from the alternator is now via a new heavy duty connector. Supplied with instructions. New connectors have to be crimped onto the wiring coming from the alternator which are supplied. This takes a few minutes but is well worth the effort.

  • Super effiecient 'MOSFET' regulator rectifier.
  • Direct fused connection to the battery to avoid common connection faults in the wiring loom.
  • Works where airlow is limited.
  • In-built thermal protection.
  • Manufactured in the UK.

 

This Electrectex unit fits Daytona 955 from vin 132512, 955 Speed Triple from vin 141872, 955 Sprint ST and Sprint RS from vin 139277, Speed Four, Daytona 600, Daytona 650, 1050 Speed Triple, 1050 Tiger and all Tiger 955.

 



£114.00
More info  

1050 ST Regulator Rectifier Electrex unit
( EG685 )

Regulator/rectifier unit for Sprint 1050  1000mm lead and aluminium alloy monting plate.

Hi-power series regulator rectifier with MOSFET technolgy. UK based company Electrex have taken a fresh look at this problem part. This is the very latest Electrex unit with direct connection to the battery terminals bypassing problems associated by going through the wiring loom. Supply from the alternator is now via a new heavy duty connector. Supplied with instructions. New connectors have to be crimped onto the wiring coming from the alternator which are supplied. This takes a few minutes but is well worth the effort.

 

  • Super effiecient 'MOSFET' regulator rectifier.
  • Direct fused connection to the battery to avoid common connection faults in the wiring loom.
  • Works where airlow is limited.
  • In-built thermal protection.
  • Manufactured in the UK.


£119.95
More info  

Generator Stator TT600, Speed 4, Daytona 600/650
( EG925 )

Electex 115mm generator Stator to fit TT600, Speed 4 and Daytona 600/650. The stator has  64 mm fixing centres and a 16 mm thick fixing flange. 



£114.00
More info  

Regulator/Rectifier TT600, Bonneville, Thruxton
( EG927 )

MOSFET regulator/rectifier unit to fit all TT600, Bonneville, T100, Thruxton, Scrambler, America and Speed master. This is a single connector unit (later units on Speed Four and Daytona have x 2 connectors) with 5 wires into a 6 way socket.



£105.00
More info  

Generator Stator 675 Daytona and Street Triple
( EG930 )

Generator/alternator with crank position sensor/trigger coil. The Electrex generator is a really excellent product and this is the latest deveopment. Previously we had advised customers to connect/reuse the original crank psition sensor as the original product always performs better. These new units from Electrex hopefully are a better and the crank sensor supplied works as well as original equipment. Fits all Daytona 675 up to VIN 564947 and Street Triple up to VIN 560476



£144.00
More info  

Headlight unit Legend, Thunderbird Sport
( EL008 )

Complete light unit with original deep black painted shell as fitted to Legend, Thunderbird Sport and Thunderbird 900 after vin 71699. Plenty of room to install wiring. Symetrical low beam (OK for UK and mainland Europe) clear lens multi surface reflector as now used on all new Triumph models. Shell depth from rim edge 120 mm

Can also be fitted to Bonneville 800/865, T100, SE, Thruxton



£119.95
More info  

Headlight unit Thunderbird Sport, Thunderbird 900, Legend.
( EL009 )

Complete light unit with original deep black painted shell as fitted to Legend, Thunderbird Sport and Thunderbird 900 after vin 71699. Plenty of room to install wiring. Choice of left, right or symetrical dipping low beam light unit. Ready to use chrome rim and black shell, with 60/55w high/low beam and side/parking light with connector. Shell depth from rim edge 120 mm.

Can also be fitted to Bonneville 800/865, T100, SE, Thruxton.





£95.00
More info  

Complete chrome headlight Thunderbird, Trident
( EL010 )

Complete with light unit with chrome shell. Light unit has 60/55w high/low beam and side/parking light with connector. Choice of left, right or symetrical low beam.

Fits Trident 750/900, Speed Triple 750/900,  Adventurer and Thunderbird.

Can also be fitted to Bonneville 800/865. T100, Thruxton, Legend and Thunderbird Sport but depth of shell is less, giving less room for electrical wiring. Overall width approximately 200mm (7 7/8")





£95.00
More info  

Complete headlight 900 Speed Triple and Trident
( EL011 )

Black shell headlight complete with chrome rim and choice of left, right or symetrical dipping low beam light unit with 60/55w high/low beam and side/parking light connector.

Fits Trident 750/900 and Speed Triple 750/900.

Can also be fitted to Bonneville 800/865. T100, Thruxton, Legend and Thunderbird Sport but depth of shell is less, giving less room for electrical wiring. Overall width approximately 200mm (7 7/8").





£95.00
More info  

Headlight support tube rubbers
( EL020 )

Set of 4 headlight support tube rubbers. Fits at the top and bottom of the headlight support tubes.

Fits:

Adventurer, Speed Triple 750/900, Legend, Thunderbird 900, Thunderbird Sport and Trident 750/900 ( black engine models from VIN 4901)



£11.95
More info  

Light unit symmetrical clear lens Bonneville EFI, Thruxton, also Trident
( EL024 )

Light unit for the larger of the round headlights used by Triumph. Latest type clear polycarbonate lens with multi-surface reflector which was introduced on models from approximately 2010.Symmetrical low beam ( left and right side driving) with side light. This style of light unit is now used on virtually all new vehicles and will replace the original headlight on the Bonneville range (not Scrambler),  America, Speedmaster, Thruxton, Thunderbird 900, Legend, Thunderbird Sport, Adventurer, 750/900 Trident and 750/900 Speed Triple models.



£39.95
More info  

Headlamp rim to fit Speed Four,955/1050 Speed Triple, Rocket 3. .
( EL026 )

Chrome headlamp rim to fit all urban round twin headlight models. Speed Four, 675 Street Triple, T509/955/1050 Speed Triple and Rocket 3.

Can also be used to replace the black headlight rim used on:Thunderbird Storm and Bonneville Bobber



£19.95
More info  

Headlight Rim Black
( EL027 )

Black headlight rim to fit:Thunderbird Storm and Bonneville Bobber.

Also can be used as a direct replacement for original chrome rim used on: Speed Four, 675 Street Triple, T509/955/1050 Speed Triple and Rocket 3



£19.95
More info  

Indicator stalk Thunderbird 900 front
( EL098 )

85mm long (exposed section) stainless steel indicator stalk to  fit 900 Thunderbird, Legend, Adventurer, Thunderbird Sport.



£19.95
More info  

Indicator black front CEV style.
( EL103 )

Front indicator to fit 750/900 Trident, 750/900/1000/1200 Daytona, 750/900 Speed Triple and 900/1200 Trophy. A slightly longer version was fitted to the 900 Sprint.

This indicator listed can be used on the rear of many models with shorter stem EL106

This indicator listed can be used on the 900 Sprint and Sprint Sport, but it will be closer to the fairing shell or the correct length longer stem EL105 can be used.



£19.99
More info  

Indicator Stalk Front Trident, Trophy, Daytona, Speed Triple 900
( EL104 )

Front indicator stalk to fit front indicators used on carburettor 3 and 4 cylinder models.

Fits: 750/900/1000/1200 Daytona, Super III, 750/900 Speed Triple, 750/900 Trident, Tiger 900 (carburettor), Trophy 900/1200 (up to VIN 29155).



£8.95
More info  

Indicator Stalk Front Sprint 900, Sprint Sport and Sprint Executive
( EL105 )

Front indicator stalk for the Sprint 900 range.

Fits: Trident Sprint, Sprint 900, Sprint Sport and Sprint Executive.



£8.95
More info  

Indicator Stalk Rear Trident, Speed Triple 900, Sprint 900
( EL106 )

Rear shorter indicator stalk for carburettor 3 and 4 cylinder models used on the rear only. 50 mm long ( 70 mm including thread)

Fits: 750/900/1000/1200 Daytona, Super III, 750/900 Speed Triple, Sprint 900, Sprint Sport, Sprint Executive, 750/900 Trident, Tiger 900 (carburettor), Trophy 900/1200 (up to VIN 29155).

 



£8.95
More info  

Xenon headlight bulb H4
( EL107 )

Xenon 60/55 w 472 H4 type headlight bulb, 30% brighter than standard. Fits all carburettor models and all 955 models.



£7.50
More info  

Headlamp rim Scrambler
( EL108 )

Chrome outer headlamp rim to fit Scrambler.



£35.00
More info  

Headlight rim Bonneville, Thunderbird, Trident, Speed Triple 900
( EL109 )

Outer chrome rim. Fits Trident 750/900,  Speed Triple 750/900, Bonneville 800/865, Thruxton, Legend, Adventurer, Thunderbird and Thunderbird Sport. Outer diameter approximately 200mm.



£29.95
More info  

Headlight rim set Bonneville, Thunderbird, Trident
( EL110 )

Complete set of headlamp rims (set of 3) and fixing screw kit complete.

Fits: 750/900 Speed Triple, 750/900 Trident, 800/865 Bonneville, T100, SE, Thruxton, 900 Thunderbird, Legend, Adventurer and Thunderbird Sport.



£49.95
More info  

6 w Halogen Side (Day Time Running) Light Bulb
( EL112 )

12 v  6 watt halogen side light bulb for day time running.

Fits: Adventurer, America, Bonneville, T100, SE, Daytona 750/900/1000/1200, Daytona Super III, Legend, Rocket, Classic, Roadster, Touring, Speed Four, Speed Triple T509, Speed Triple 955, Speed Triple 1050 up to VIN 461331, 750/900 Speed Triple, Speedmaster, Sprint 900, Sprint Executive, Sprint Sport, Thruxton 900, Thunderbird 900, Thunderbird Sport, Tiger 900 (carburettor), 750/900 Trident



£2.99
More info  

Light unit , pattern (Trident, Thunderbird, Legend etc)
( EL121 )

Light unit to fit Trident 750/900, Thunderbird 900, Speed Triple 750/900, Thunderbird Sport, Adventurer, Legend.

This fluted glass lens light unit also fits all Bonneville, Thruxton, T100, America SE, and Speedmaster models. From approximately 2010 EFI models had a plain/clear lens light unit fitted, our part number EL024. All the light units interchange and you can just choose the style of lens you prefer.

Available in left, right or symmetrical low (dip) beam.





£24.95
More info  

Speed Triple twin headlight pivot
( EL152 )

Replica T509/955 Speed Triple headlight pivot on models up to 2002 , used on twin headlamp assembly. 70mm hole centres.



£26.00
More info  

Headlight support brackets 41 - 43 mm
( EL169 )

Black headlight support brackets to fit fork tubes from 41 - 43 mm. Sold as a pair.



£35.00
More info  

Front Indicators x 2 to fit TT600 and Speed Four
( EL175 )

x 2 front indicators to fit TT600 and Speed Four complete with wiring and correct connectors. Sold as a pair.



£29.00
More info  

Indicator stalk rear Thunderbird 900
( EL340 )

45mm long (exposed section) stainless steel indicator stalk to  fit 900 Thunderbird, Legend, Adventurer, Thunderbird Sport



£19.95
More info  

LED Rear Light 675
( EL341 )

Clear lens LED rear light and built in indicators to fit 675 Daytona and Street Triple models

675 Daytona, 675 Street Triple



£69.00
More info  

Headlight, twin replacement Speed Triple (Pair)
( EL391 )

Direct replacement flat glass symetrical dip/low beam light units with headlight bulbs and side light hole. Supplied as pairs, as the units although similar are not exactly the same as the originals.

Fits T509, Speed Triple 955, Speed Triple 1050, Speed Four, Street Triple



£69.00
More info  

Indicator left. Daytona T595, 955, T509 Speed Triple
( EL403 )

Left side front indicator complete (also right side rear) with correct wiring which connects into original Triumph wiring loom.

T509, Daytona T595, 955 Daytona, 955 Speed Triple.



£14.95
More info  

Indicator right. Daytona T595, 955, T509 Speed Triple
( EL404 )

Right side front indicator complete (also left side rear) with correct wiring which connects into original Triumph loom.

T509, Daytona T595, 955 Daytona, 955 Speed Triple.



£14.95
More info  

Indicator left 1050 Speed Triple, 800 Tiger
( EL405 )

Left front or right rear indicator complete with wiring which connects into original Triumph connector on loom and correct stems as original.

Fits Street Triple 675, 800 Tiger, 800 Tiger XC, XRx, XCx, Daytona 675 from VIN 381275,1050 Tiger from VIN 48357 and Tiger Sport.



£19.95
More info  

Indicator right 1050 Speed Triple, 800 Tiger
( EL406 )

Right front or left rear indicator complete with wiring which connects into original Triumph connector on loom and correct stems as original.

Fits Street Triple 675, 800 Tiger, 800 Tiger XC, XRx, XCx, Daytona 675 from VIN 381275,1050 Tiger from VIN 48357 and Tiger Sport.



£19.95
More info  

Indicator Lens 675, 800, 1050
( EL407 )

Fits Street Triple 675, 800 Tiger, 800 Tiger XC, XRx, XCx, Daytona 675 from VIN 381275,1050 Tiger from VIN 48357 and Tiger Sport.



£4.95
More info  

Indicator stalk 675, 1050
( EL408 )

UV attacking the plastic stalk ? Bought a pattern indicator with incorrect stalk ? Broken indicator stalk ?  Here's the fix. This fits both oval and wedge style indicators.

Indicator stalk to fit all Street Triple 675, 800 Tiger, 800 Tiger XC, XRx, XCx, Daytona 675, Tiger 1050, Tiger Sport, Tiger Explorer (rear), Daytona 600/650 and Sprint ST 1050 (rear).

 

 



£3.95
More info  

Indicator
( EL410 )

Right front and left rear indicator.

Fits: Daytona 600, Daytona 650, 675 Daytona up to VIN 381274 and 1050 Tiger up to VIN 483576.



£19.95
More info  

Indicator
( EL411 )

Left front, right rear indicator.

Fits: Daytona 600, Daytona 650, 675 Daytona up to VIN 381274 and 1050 Tiger up to VIN 483576.



£19.95
More info  

Light Unit Diamond Reflector (Right Hand Dip), Street Triple, Speed Triple and Speed 4
( EL752 )

Sold as a pair, these replace the smaller of the round headlights used by Triumph and are for use on right side low beam (Continental dip only). Clear glass lens, multi surface (diamond) reflector light, with side light, they can be fitted to 675 Street Triple, 955/1050 Speed Triples, Speed 4 and Rocket 3 models.



£89.00
More info  

Speedmaster and America spot light unit
( EL880 )

Replacement multi surface reflector light unit straight fit into Triumph auxilary lights used on Speedmaster, America and Thunderbird 1600/1700 models. Supplied complete with H3 bulb. Manufactured by Jute. Quantity x 1.

Fit Speedmaster, America and Thunderbird 1600/1700.



£39.00
More info  

Thunderbird 900 silencers off road.
( EX023 )

Silencers to fit Thunderbird 900, Legend and Adventurer. Fitted with removable baffles. These are not road legal and do not make the same type of noise as a 3:1 system. The original arrangement of two exhaust pipes exiting to the right and a single pipe exiting to left gives a unique slightly unbalanced sound especially to the driver. It's like the original fully silenced exhaust sound but much louder.

Picture on a Legend look at  http://www.triumphtorque.com/media/file/82747.aspx

Sold as a pair.

 

 

 

 



£189.00
More info  

3:1 exhaust for Thunderbird 900 Legend and Adventurer
( EX025 )

Stainless steel 3:1 header pipes with chrome silencer to fit Thunderbird 900, Legend TT and Adventurer.



£479.00
More info  

3:1 stainless steel exhaust system
( EX078 )

3:1 stainless steel system complete with Viper alloy sleeved and stainless steel ended silencer fitted with a removable baffle. System does not have a centre stand stop. A centre stand can be used, but a return stop will have to made/fitted. Oil and filter changes can be completed without removing the exhaust.

750/900 Trident, 900 Trophy, 750/900 Speed Triple, 750/900 Daytona, 900/1200 Trophy <96 and 900 Thunderbird Sport 



£495.00
More info  

3:1 system with choice of oulet size 38, 45, 51 mm Trident, Speed Triple 900
( EX080 )

Stainless steel 3:1 down pipes with intermediate connector pipe. Available to  accept 38 mm, 45 mm or 51 mm for silencers. Available for all Tridents, Daytona 750/900, all Sprint 900 models (except Executive), Sprint Sport, Speed Triple 750/900 and all Trophy 900 up to vin 29154. Thunderbird 900, Legend and Adventurer. Also available to fit 1200 models to special order, just ask.





£389.00
More info  

Exhaust studs steel, all 3 cylinder models
( EX083 )

Set of 6 steel exhaust studs.  (M8 x 1.25 pitch thread both ends)  Approximately 38mm overall length. All  3 cylinder models.



£9.95
More info  

Exhaust studs steel, all 4 cylinder models
( EX084 )

Exhaust studs to fit all 4 cylinder models. Approximately 38mm overall length. Fits all 4 cylinder models.

 



£11.95
More info  

Exhaust port/header pipe copper gasket rings (round port, priced each)
( EX086 )

Round exhaust port gasket fits all  3 and 4 cylinder carburettor models as well as the 800/865 twins, 900 injection Tiger, T509 Speed Triple, TT600, Speed Four and Daytona 600/650.

750/900 Trident, 750/900 Speed Triple, 600/650/750/900/1000/1200 Daytona, 900/1200 Trophy, Thunderbird 900, Legend, Thunderbird Sport,  Adventurer, Tiger 900, Tiger 900 injection, T509 Speed Triple, TT600, Speed Four,



£1.75
More info  

Exhaust Port Seal Street Twin, Cup, Thruxton 1200
( EX095 )

Copper exhaust header/cylinder seal. Sold as a pair.

Fits: Bonneville Bobber, Bonneville T120, Street Cup, Street Scrambler, Street Twin, Thruxton 1200, Thruxton R,



£3.95
More info  

Exhaust connectors for Tiger 900
( EX254 )

Stainless connectors for carburettor model Tiger 900 for fitting aftermarket 51mm bore silencers. Outlet size approx 51mm. (Priced per par)



£124.95
More info  

Exhaust connector 900/955 Tiger models
( EX299 )

Connector fits original exhaust front pipe of all injected 900 and 955 Tiger models to allow fitting of aftermarket 2" (51mm)  inlet silencer.



£49.00
More info  

Exhaust connector 955 Sprint RS
( EX300 )

Connector to allow fitting of 2" (51mm) inlet bore size aftermarket silencer.



£49.00
More info  

Exhaust connector 955 Speed Triple.
( EX336 )

Fits clamp type fitting downpipes on 2002> 955 Speed Triple models to allow 2" (51mm) aftermarket silencer to be fitted. Original exhaust downpipe outlet should be 44/45mm.



£49.00
More info  

Tiger 1050 Exhaust connector
( EX355 )

Stainless steel polished connector for fitting after market exhaust can to 1050 Tiger models.  An oval shaped can makes fitting easier.



£79.00
More info  

Exhaust connector 800 Tiger
( EX356 )

Exhaust connector to fit race can to 800 Tiger models. Outlet size approximately 50.5mm.



£65.00
More info  

Exhaust lower kit for 900/1200 Daytona, 900 Speed Triple and Sprint Sport
( EX484 )

Silencer lower kit for 900/1200 Daytona, 900 Speed Triple and Sprint Sport. Normally used when luggage is fitted. The connector pipes can also be used for a reverse use to raise/kick up silencers.



£49.00
More info  

Exhaust studs steel. Bonneville range
( EX628 )

x 4 steel exhaust studs and flanged nuts.

Fit Bonneville 800/865, T100, Scrambler, America, Speedmaster, SE, Thruxton



£6.75
More info  

Exhaust Clamp 40-43 mm
( EX669 )

Stainless steel exhaust clamp with internal range from 40 to 43mm diameter.



£4.95
More info  

Exhaust Clamp 43-47 mm
( EX673 )

Stainless steel exhaust clamp with internal range from 43 to 47mm diameter.

Silencer clamp size for 955 Sprint ST and RS



£4.95
More info  

Exhaust Clamp 47-51 mm
( EX674 )

Stainless steel exhaust clamp with internal range from 47mm to 51mm diameter.



£4.95
More info  

Exhaust Clamp 51-55 mm
( EX675 )

Stainless steel exhaust clamp with internal range from 51 to 55mm diameter.



£4.95
More info  

Exhaust Connector
( EX677 )

Chrome connectors to raise the low level silencers on 750/900 Trident after VIN 4901 (black engine model), Trophy 93-95 (grey frame and engine model) and Sprint 900 to the higher level of the Sprint Sport and Speed Triple. The connector fits between the the downpipes and the silencer to kick them up to the new position. Speed Triple or Sprint Sport exhaust hangers will need to be fitting. Sold as a pair.

If exhaust clamps are required use product code EX669



£39.00
More info  

Frame finishers stainless steel
( F001 )

Polished stainless steel frame finishers (Outrigger Finisher Kit). Frame finishers were originally supplied by Triumph as chrome plated accessories and aimed at 900 Thunderbird, Adventurer and Legend owners. These will also fit all steel frame 3 and 4 cylinder models from 1991 to 2004. Supplied as a set of 4.

Fits: Adventurer, Daytona 750, 900, 1000, 1200, Legend, 750 & 900 Speed TripleSprint 900, Sprint Sport, Sprint Executive, Thunderbird 900, Thunderbird Sport,Tiger 900 (carburettor), 750 & 900 Trident, Trophy 900 & 1200 (up to VIN 29155).

 



£89.00
More info  

Gear Change Rubber Thunderbird, Bonneville, Tiger 800
( F088 )

Gear change rubber to fit Thunderbird 900, Legend, Thunderbird Sport, Adventurer, Bonneville 800/865, T100, America, Speedmaster and Tiger 800, Tiger XC, Tiger XCX and Tiger XRX.



£2.95
More info  

Gear change lever rubber
( F089 )

These are very high quality gear change rubbers, which will outlast the original part.

To Fit:

Sprint 900, Sprint Sport, Sprint Executive and Trident Sprint.

Speed Triple 750/900

Trophy 900/1200

Trident 750/900

Daytona 750, 900, 1000, 1200

Tiger 900 carburettor and injection (EFI)

Tiger 955

TT600 and Speed Four

Sprint 955 RS and 955 ST

Daytona T595 and 955 from VIN 87317 (one piece 'reverse' gear lever)

Speed Triple 955 from VIN 87317 (one piece 'reverse' gear lever)



£1.75
More info  

Foot Rest, Left
( F093 )

CNC machined from aircraft specification aluminium HE 30 6082 T, super strong replacement footpegs for Trident, Trophy, Sprint 900, Sprint 955 RS and ST.  Natural anodized finish. These accept original footrest rubbers and hero blobs. Made in UK



£23.00
More info  

Foot Rest, Right.
( F094 )

CNC machined from aircraft specification aluminium HE 30 6082 T, super strong replacement footpegs for Trident, Trophy, Sprint 900, Sprint 955 RS and ST.  Natural anodized finish. These accept original footrest rubbers and hero blobs. Made in UK.



£23.00
More info  

Foot Rests with rubber and hero blob, can be fitted to Trident,Trophy/Daytona 900/1200, 955 ST/RS
( F096 )

Wider than the original components (not as wide as twin headlamp Trophy/955 Tiger), complete replacement front footpegs for early models. 750/900 Trident, 750/900/1000/1200 Daytona and 900/1200 Trophy. Also they will fit 955 Sprint ST/RS. Sold as a pair.



£34.95
More info  

Foot Rest Rubbers Carburettor 3 and 4 Cylinder Models
( F099 )

Footrest rubbers fit 750/900/1000/1200 Daytona, 750/900 Trident, 750/900 Speed Triple, 900/1200 Trophy (single headlamp model), Trident Sprint, Sprint 900, Sprint Sport, 955 Sprint ST (front), 955 Sprint RS (front) Sold as a pair.

Rear footrest rubbers on Tiger 900 (carburettor) models.

New Replacement Footrest Rubbers complete with new Stainless Steel fixing screws to fit Trident 750. The rubbers are manufactured from a harder wearing polymer material than original OE. The shape, size and fitting of these replacement rubbers is the same as the original. Sold as a pair.



£9.95
More info  

Riders Foot Rest with rubbers for extra grip available for T.595/955 Daytona
( F162 )

Footrest with rubber and hero blob fit T595, T509, all 955 Daytona and 955 Speed Triple all models. Sold as a pair.



£34.95
More info  

Gear Change Rubber 675, 1050, Thruxton
( F168 )

Gear change rubber to fit Thruxton, 675 Daytona, Street Triple, Tiger Sport, Tiger 1050, 1050 Sprint ST, Speed Triple 1050, Tiger Explorer and Tiger Explorer XC.



£1.95
More info  

Lever Bush 3 and 4 Carburettor Models. 18mm.
( F620 )

Ptfe coated pivot bush used on gearchange and brake pedal for all 3 and 4 cylinder carburettor models. Internal size 18mm.

750/900 Trident, 900/1200 Trophy, 750/900/1000/1200 Daytona, 750/900 Speed Triple, 900 Sprint, Sprint Sport, Sprint Executive,



£4.25
More info  

Lever Bush T595/T509/955 (16mm)
( F621 )

Brake pedal and gear change pivot bushes to fit Speed Triple T509, Daytona T595, 955 Speed Triple up to vin 141872 and Daytona 955 up to vin 132513.



£4.25
More info  

Lever bush 955 ST/RS 600/650 Thruxton Tiger (12mm)
( F622 )

Brake pedal pivot bush for Tiger 900, Tiger 955, Bonneville Thruxton, TT600, Speed Four, Daytona 600 and 650.

Gear change pedal pivor bush for Tiger 900, 955 Sprint ST, Sprint RS and 1050 Sprint ST.

Internal size 12mm.



£4.25
More info  

Rear Brake Pedal Bush Thunderbird 900, Speedmaster
( F623 )

Rear brake pedal pivot bush to fit Speedmaster, America, Scrambler, 900 Thunderbird, Adventurer and Legend



£3.95
More info  

Gear Change Lever Pivot Bush
( F624 )

Fits gear change and rear brake pedal on Thunderbird Sport.

Fits gear change pedal only on Speedmaster, America and Rocket 3.

Fits rear brake pedal only on Bonneville, T100 and SE.



£3.95
More info  

Gear change connecting rod Sprint 955 ST and RS
( F625 )

Stainless steel gear change rod to fit 955 Sprint ST ans RS up to vin 139276. Steel steel rod is a total length of 135 mm long with a right hand and left hand M6 thread.



£12.50
More info  

Cover/Boot Gear Change Ball Joint
( F630 )

Gear change ball joint end pivot boot/cover. All models.



£2.95
More info  

Sprint fairing lowers (to fit genuine Sprint 900 fairings) - unpainted
( FR237 )

Fairing lowers to make the Sprint 900 range into a fully faired bike. Panels are complete with all screws and fitting brackets. Supplied as a pair and require painting.

Fits Trident Sprint, Sprint 900, Sprint Sport and Sprint Executive.



£229.00
More info  

Sprint fairing lowers (to fit genuine Sprint 900 fairings) - painted
( FR865 )

Colour matched painted glass fibre fairing lowers and fitting kit to fit Trident Sprint, Sprint 900, Sprint Sport and Sprint Executive.

4 week delay while panels are painted to order.





£375.00
More info  

Mikuni Inlet Rubber (Cylinder Head to Carburettor)
( G005 )

Triumph have used Mikuni and Keihin carburettors. This part fits models with Mikuni carburettors and is an unrestriced inlet rubber.

As original fitment on 750/900/1000/1200 Daytona, Daytona Super III, 750/900 Speed Triple, Trident Sprint, Sprint 900, Sprint Executive, Sprint Sport, 750/900 Trident, 900/1200 Trophy and 900 Tiger (carburettor).

The 900 Thunderbird range used restricted inlet rubbers (G003) to give more bottom end performance at the expence of mid range and top end. So you can also choose to fit these to the following models instead of the restriced inlet rubber. Adventurer, Legend, Thunderbird 900 and Thunderbird Sport. 

 



£5.95
More info  

Mikuni (Air Box to Carburettor) Rubber
( G010 )

Triumph have used Mikuni and Keihin carburettors. This fits all Mikuni carburettor models from air box to carburettor.

Fits:  Adventurer, 750/900/1000/1200 Daytona, Daytona Super III, Legend, 750/900 Speed Triple, Thunderbird 900, Thunderbird Sport, Trident Sprint, Sprint 900, Sprint Executive, Sprint Sport, 750/900 Trident, 900/1200 Trophy and 900 Tiger (carburettor).

Priced each including stainless steel band clip.

 



£6.95
More info  

Rear hugger only, gloss black glass fibre extended below swinging arm to protect suspension links. Available for T595/955/Daytona/Sprint ST
( G161 )

Fits T595, T509, 955 Daytona (single sided swinging arm), 955 Speed Triple, 955 Sprint ST and 955 Sprint RS from vin 161318. Extends below the swinging arm to protect the suspension linkage.

Can also be fitted to 1050 single sided swinging arm models if 6mm hole is drilled/tapped on right front of arm. Made in UK.



£89.00
More info  

Touring front guard rear section Trophy 900/1200 and 955/1050 ST/RS.
( G163 )

Super long replacement gloss black section for rear of front guard.  215mm (8.5") longer than the original guard. Total length 57cm (22 1/2"). This fits all 955 Sprint RS, 955 Sprint RS, 1050 Sprint ST and 900/1200 from vin 29156. Made in UK from glass fibre.



£49.95
More info  

TT600 and Speed Four Front Guard Extender
( G311 )

Short black plastic front guard extender to fit TT600 and Speed Four



£19.95
More info  

Front guard extender Thunderbird 900 and Legend
( G313 )

Satin black plastic front guard extender to fit Thunderbird 900, Adventurer and Legend TT. 



£19.99
More info  

Mudguard extender front 955 Sprint RS/RT, Trophy, 1050 ST
( G314 )

Front guard extender. Fits 955 Sprint RS/ST, 1050 ST, 1050 GT and 900/1200 Trophy from VIN 29156 (twin headlamp models).



£19.95
More info  

Front guard extender 1050 Tiger, 955/1050 Speed Triple, 955 Daytona
( G317 )

Front guard extender to fit 955 Speed Triple (VIN 141872>),  955 Daytona (VIN 132513>), 1050 Tiger and 1050 Speed Triple.



£19.99
More info  

Mudguard extender front 900 Tiger
( G320 )

 Satin black plastic front guard extender to fit all carburettor model 900 Tiger.



£19.99
More info  

Mudguard extender rear
( G321 )

Fits 750/900 Trident, 900/1200 Trophy (for the 2013> Trophy see product code 609), 750/900/1000/1200 Daytona, 900/955 Tiger and 955 Sprint RS/ST.



£24.00
More info  

Tiger 955 front guard extender
( G324 )

Stain black plastic front guard extender to fit all 955 Tiger and also Tiger 900i.



£19.99
More info  

Fenda extender front Trident, Trophy etc
( G343 )

Fits 750/900 Trident, 900/1200 single headlight model Trophy, 750/900/1000/1200 Daytona and 750/900 Speed Triple.



£19.99
More info  

Front mudguard extender 675 Daytona and Street Triple
( G409 )

675 Daytona up to VIN564974 and 675 Street Triple up to VIN560477



£19.99
More info  

Rear hugger Tiger 955 2005> (cast wheel model)
( G591 )

Black gloss glass fibre rear hugger kit with integral chainguard to fit the last of the 955 Tiger from vin 198875



£89.00
More info  

Trophy 2013 Rear guard Extender
( G609 )

Rear guard extender easy predrilled easy fit to new 1200 Trophy tourer. Black grained finish.



£39.95
More info  

Front guard 1050 ST, 955 RS/ST and Trophy
( G680 )

1050 ST style black gloss front section to fit 955 Sprint ST, 955 Sprint RS, 1050 Sprint ST and 900/1200 Trophy models after vin 29156 (dual headlight models)



£76.00
More info  

Front guard Trident, Daytona 900/1200, Speed Triple 900
( G875 )

Very high quality glass fibre reinforced replica of the original Trident/Trophy/ Daytona and Speed Triple (carburettor model) front guard. Supplied in gloss black only.  With spacer blocks from early models can also be fitted to the 955 Sprint ST and RS models. Fits 750/900 Trident, 900/1200 Trophy, Sprint 900, Sprint Sport, Sprint Executive and 750/900 Speed Triple. Made in UK.



£99.00
More info  

Rear Hugger Tiger 1050
( G880 )

Rear hugger in rigid gloss black glass fibre to fit all Tiger 1050 (not Tiger Sport)



£89.00
More info  

955 Sprint ST and RS Handlebar riser blocks (priced per pair)
( H012 )

Anodized aluminium alloy riser blocks to raise 955 RS handlebars 33mm to ST level. Can also be used to raise ST 955 handlebars. Sold as a pair.

Sprint 955 ST from vin 139277 requires a longer front brake hose. Product code H016.

Fits 955 Sprint RS, Sprint 955 ST

AWAITING NEW STOCK

 



Contact Us For Details

Adaptor block for fitting one piece handlebars
( H015 )

Removing the original handlebars and fitting this CNC machined block allows 7/8" tubular steel bars to be fitted.This block fits in place of the original handlebars used on Trident, Trophy, Daytona 900/1200 and Sprint 900 models. Cable lengths may need changing or rerouting if higher bars are fitted. The block is supplied with the fixing screws and handlebar clamps. Colour black (anodized finish).

 

750/900 Trident, 750/900/1000/1200 Daytona, Sprint 900, Sprint Sport, Sprint Executive, Trophy 900/1200



£119.00
More info  

Brake hose 25 mm longer than standard 955 ST
( H016 )

Longer front brake use to fit with handlebar riser blocks on Sprint 955 ST from vin 139277. Stainless steel crimped banjo ends with original type 90 degree bend from master cylinder. These includes two stainless steel banjo bolts and sealing wshers. Made in UK.



£46.00
More info  

Handlebars to fit Thunderbird Sport
( H087 )

Chrome plated handlebars for Thunderbird Sport , with 5mm threaded recessed ends to accept original bar end weights and holes for locating the switches. Bar diameter 7/8" (22 mm) Made in UK.

73 cm (28 3/4") wide, 40 cm (1 5/8") rise and 90 cm (3 1/2") pull back 

 



£39.00
More info  

Handlebars to fit Thunderbird and Legend
( H088 )

Chromed plated handlebars to same exact shape as 900 Thunderbird. Although they are a slightly different shape, they can also be fitted to the Legend. They have 5mm threaded recessed ends to accept original  bar end weights and location holes for handlebar switches. 7/8" (22 mm) diameter tubing. Made in UK

900 Thunderbird/ 900 Legend

720 mm wide (28 "), 150 mm (6 ") rise and 210 mm (8") pull back.



£39.95
More info  

Bar end weights to fit Daytona T595/955, 955 Speed Triple and Thruxton, black steel (priced per pair)
( H090 )

Gloss black coated steel bar end weighs (150 gram each) to replace original black aluminium alloy bar end weights. These are much heavier to change the natural vibration/frequency.  Sold as a pair. Will fit handlebars with tubular (not solid) section at the end to a depth of 52 mm with18 mm inside diameter required. Bar end weight is 25 mm outside diameter. 

Fits T509, T595, 955 Daytona up to vin 132513, 955 Speed Triple and Thruxton.



£12.95
More info  

Bar end weights to fit...
( H116 )

Black coated aluminium bar replacement weights. Sold as a pair.

Fit T509, T505, 955 Daytona (up to vin 132513), Thruxton.



£7.95
More info  

T509/955/1050 Speed Triple handlebars
( H156 )

Chrome 7/8 " (22 mm) handlebars manufactured in the UK to the original size & shape with drilled holes for locating switch gear and knurled grip areas for the bar clamps. 

Fits:  Speed Triple T509, 955 & 1050 Speed Triple up to VIN 333178.

735 mm (29 ") wide, 70 mm (2 3/4 ") rise and 115 mm (4 1/2") pull back.

 

 



£39.00
More info  

T595 and early 955i handlebar riser kit, 38mm extra rise
( H157 )

Over 1 1/2" extra rise over standard bar position with these beautifully CNC machined risers from aircraft specification aluminium HE 30 6082 T6. To fit all T595 and early 955i Daytona models up to vin number 105630. These can be adapted to later model 955 Daytona if earlier style handlebar components are used. Triumph supplied the bars with 2 different size 1/2 clip/clamp pivot pivs 5mm or 6.5mm. We only have 6.5 mm now in stock. Measure pin size on underside where circlip fits. Supplied as a pair.

 

 

 



£124.95
More info  

Handlebar pivot pin T595 and early 955 Daytona.
( H159 )

Stainless steel pivot pin used on the first series handlebars on T595 and 955i Daytona models. Please check pin size. Choose 5 mm or 6.5 mm.





£9.95
More info  

Handlebar R/h T595/955 Daytona
( H160 )

Replacement bar  for all T595 and 955 Daytona up to approximately 1999 with multipiece clip-on design.



£19.00
More info  

Haynes Repair Manual, Bonneville, T100, Speedmaster, America and Thruxton
( H211 )

Bonneville 800/865, T100, SE, Speedmaster, America,  Scrambler, Thruxton. 2001 - 2012.



£19.99
More info  

Haynes Repair Manual, Bonneville (water cooled), T100, T120, Bobber, Street Twin
( H213 )

Haynes manual for water cooled twins. Bonneville T100, T120, Bobber, Thruxton, Street Twin, Cup and Scrambler. 2016 on.



£19.95
More info  

Haynes 675 Daytona and Street Triple Manual
( H218 )

Haynes service and repair manual for the 675 range  (2006 to 2010). Daytona 675, Street Triple and Street Triple R.



£19.99
More info  

Haynes repair manual, 900 fuel injected and 955 Models
( H220 )

All fuel injected 900 and 955 models.



£19.99
More info  

Haynes Repair Manual, 1050 SprintST, Speed Triple & Tiger Repair Manual
( H221 )

Repair manual for 05-09 1050 Sprint ST, 1050 Speed Triple and 1050 Tiger.

1050 Sprint ST, 1050 Speed Triple, 1050 Tiger



£19.99
More info  

Adjustable handlebars 43 mm forks for 900 Speed Triple with 35mm or 70mm rise.
( H269 )

Suitable for 750/900 Speed Triple models (Providing there is fairing clearance, the 70 mm version can also be fitted to other 43mm fork models. The 900 and 1200 Daytona have approximately 35 mm rise on the original Triumph handlebars) these adjustable bars have an anodised aluminium finish with black bar end weights.

 





£159.95
More info  

Adjustable clip on handlebar with 70mm riser for 45mm fork size
( H270 )

Fully adjustable clip on handlebar set with 70 mm rise, ideal for adapting to 2000 on 955 Daytona models which have the one piece construction clip on handlebars. Original handlebars have 35 mm rise as standard. These fully adjustable clip on handlebars give an extra 35 mm rise to reduce weight on wrists.

 

 





£159.95
More info  

Clip-on Habndlebars 41 mm
( H275 )

41 mm 'old school' welded steel clip-on handlebars for cafe racer conversions on the Bonneville, T100 and Thruxton. Available black or chrome finish. No location holes for the standard switchgear have been drilled. Sold as a pair.





£49.95
More info  

Haynes Manual Tiger 800 Range
( H682 )

Haynes workshop manual for the Tiger 800 range. Specifically aimed at 2010 - 2014 Tiger and Tiger XC including ABS.



£19.99
More info  

Handlebar end weight stainless steel. Trident, Trophy, Sprint 900
( H691 )

Replacement stainless steel handlebar end weight and fixing screw to fit 750/900 Trident, 750/900 Speed Triple, 900/1200 Daytona, 900/1200 Trophy, 900 sprint and Sprint Sport.



£14.95
More info  

Handlebar End Tiger 900 (Aluminium Alloy)
( H692 )

Original type anodised aluminum alloy handlebar end fitted to Tiger 900 (carburettor models) 1993 - 1998. Same size and shape as stainless steel handlebar end, product code H691. Supplied with stainless steel fixing screw.

Can also be fitted to 750, 900, 1000, 1200 Daytona, 750/900 Speed Triple, 750/900 Trident and 900/1200 Trophy. This is lighter than the standard stainless steel handlebar end used on these models.

 



£12.95
More info  

Dip stick Trident, Sprint 900, Tiger 900, Trophy
( J002 )

Black anodized billet aluminium alloy dip stick with stainless steel level rod. Throw away that badly moulded cross threading plastic dip stick and replace it with this lovely piece of workmanship - almost too good to use.

Fits, Trident 750/900, Sprint 900, Trident Sprint, Sprint Sport, Sprint Executive, Tiger 900 (carburettor), Daytona 750/900/1000/1200, Speed Triple 750/900, Trophy 900 and Trophy 1200 grey engine.

A few very early models had very fine threaded dip sticks (only up to vin 3926) which we only stock in plastic.

 



£25.00
More info  

Fuel pipe set
( J003 )

Fuel pipes and vacuum pipe to fit all models with vacuum operated fuel tap and Mikuni carburettors (Not Tiger 900 and Thunderbird 900 range). 

750/900 Trident, 900/1200 Trophy, 750/900/1000/1200 Daytona, Sprint 900, Sprint Sport, Sprint Executive, and 750/900 Speed Triple.

 

 



£28.95
More info  

Fuel Filler Cap Seal
( J005 )

Water in the fuel tank ?  Make sure the water drain hole (from under filler cap to rubber pipe on rear of fuel tank) is clear.  The fuel filler cap seal is supplied bonded to a plated steel dished plate and is a direct swap for the original part. When the filler cap is closed this seals against the fuel tank filler neck and is supplied with no springs, original parts are required to be reused. The third and forth pictures on this listing are of a complete filler cap just to show where the seal fits. This listing is not for a complete filler cap !

Fuel filler cap metal bonded seal fits 750/900 Trident. 750/900 Speed Triple, 900/1200 Trophy, Tiger 900 (carb), Trident Sprint, Sprint 900, Sprint Sport, Sprint Executive, Super III and 750/900/1000/1200 Daytona.



£12.95
More info  

Locking filler cap Bonneville, Thunderbird
( J013 )

Chrome locking filler cap with 2 keys to fit Bonneville 800/865, T100, Thruxton, Scrambler, Street Scrambler, Street Cup, Street Twin, Thunderbird 900, Legend, Thunderbird Sport, Adventurer, Rocket III, Touring, 1600/1700 Thunderbird, Thunderbird Storm, LT and Commander.  We now supply a choice of x 2 sealing rings with each cap. The thinner of the seals allows the filler cap to fit very close to the surface of the tank. The thicker seal gives a more practical clearance so the cap can be easily removed even with motorcycle with gloves on.



£34.95
More info  

Fuel Filler cap 600, 650, 675, 800, 955, 1050
( J017 )

Replacement filler cap and 2 keys.

Fits 600/650/675/955 Daytona, 955/1050 Speed Triple, Speed Four, Sprint ST 955, Sprint RS 955, Sprint ST 1050, 955/1050 Tiger, 675 Street Triple, Tiger 800, Tiger XC, T595, T509



£49.95
More info  

Fuel tap knob aluminium
( J025 )

Beautifully CNC machined black anodized aluminium alloy fuel tap knob.

Fits 750/900 Trident, 750/900/1000/1200 Daytona, 900/1200Trophy, 750/900 Speed Triple, Sprint 900, Sprint Sport, Sprint Executive.

 

 

 



£25.00
More info  

Petrol tap seal rebuild kit for vacuum tap on carburettor 3 and 4 cylinder models.
( J027 )

Fuel tap full rebuild kit for all 3 and 4 cylinder carburettor models except models with manual tap (900 Tiger, Thunderbird, Legend, Thunderbird Sport and Adventurer). The seals for this vacuuum operated tap include the diaphragm/plunger assembly.

750/900 Trident, 900/1200 Trophy, 750/900/1000/1200 Daytona, 900 Sprint, Sprint Sport, Sprint Executive, 750/900 Speed Triple



£23.95
More info  

Vacuum Fuel Tap Assembly Trident/Trophy/Daytona
( J028 )

Fuel tap for early carburettor 3 and 4 cylinder models (vacuum operated type). Complete tap less the control knob.

Fits:
Daytona 750/900/1000/1200, Speed Triple 750/900, Sprint 900, Sprint Executive, Sprint Sport, 750/900 Trident, 900/1200 Trophy



£65.00
More info  

Fuel Tap Seals
( J029 )

x 2 Fuel tap seals to fit 750/900 Trident, 750/900 Speed Triple, 900/1200 Trophy, Trident Sprint, Sprint 900, Sprint Sport, Sprint Executive and 750/900/1000/1200 Daytona.



£2.35
More info  

Mikuni Main Jet
( J030 )

The more popular Mikuni main jet sizes. Sold individually.





£3.50
More info  

Fuel tap seals Thunderbird 900, Tiger 900 and Bonneville 800/865
( J035 )

Tap spindle seal and face seal to fuel tank. This will fix a fuel tap if the fuel is leaking to the outside of the tap, but will not stop fuel going through the tap to the carburettors when turned off.

Bonneville 800/865, T100, SE, Thruxton, Speedmaster, America, Thunderbird 900, Legend, Thunderbird Sport, Adventurer, 900 Tiger (carburettor)



£7.95
More info  

Mikuni Diaphragm
( J040 )

Genuine Mikuni diaphragm to fit all Mikuni carburettors used on Triumph models.

Fits: Adventurer, Daytona 750/900/1000/1200, Daytona Super III, Legend TT, Speed Triple 750/900, Sprint 900, Sprint Executive, Sprint Sport, Thunderbird 900, Thunderbird Sport, Trident 750/900, Tiger 900, Trophy 900/1200



£10.65
More info  

Mikuni Carburettor Top Aluminium
( J070 )

Mikuni replacement carburettor top manufactured from black anodized aluminum. Work of art. Fits all Mikuni carburettor Triumph models and is a direct replacement for the plastic top. No plastic vacuum take off tube to brake off.

Fits: Adventurer, Daytona 750/900/1000/1200, Daytona Super III, Legend TT, Speed Triple 750/900, Sprint 900, Sprint Executive, Sprint Sport, Thunderbird 900, Thunderbird Sport, Trident 750/900, Tiger 900, Trophy 900/1200

AWAITING NEW STOCK



Contact Us For Details

Mikuni Piston Spring
( J072 )

Mikuni carburettor piston slide return spring. Replaces Triumph part number 1240040-T0301.

Diameter 9.5 mm. 97 mm long. For all Mikuni carburettors used on Triumph models.

Fits: Adventurer, Daytona 750/900/1000/1200, Daytona Super III, Legend TT, Speed Triple 750/900, Sprint 900, Sprint Executive, Sprint Sport, Thunderbird 900, Thunderbird Sport, Trident 750/900, Tiger 900, Trophy 900/1200

 



£4.95
More info  

Mikuni float needles x 3
( J076 )

Set of x3 Viton tipped float needles to fit Mikuni carburettors. These do not fit Keihin carburettors. If the carburettors are flooding, before changing the float needles, check that the two 'O' rings on the float holder (where it pushes into the main carburettor body) have not hardened with age. Triumph recommend that after fitting new float needles the float heights should be checked and set at 14.5 mm. With the carburettors inverted and the floats resting, measure from the float chamber joint face to the top of the float, this should be 14.5 mm.

We stock seal kits for Mikuni and Keihin carburettors.

Fits: Adventurer, Daytona 750/900, Daytona Super III, Legend TT, Speed Triple 750/900, Sprint 900, Sprint Executive, Sprint Sport, Thunderbird 900, Thunderbird Sport, Trident 750/900, Tiger 900, Trophy 900



£19.95
More info  

Mikuni float needles x 4
( J078 )

Set of x4 Viton tipped float needles to fit Mikuni carburettors. These do not fit Keihin carburettors. If the carburettors are flooding, before changing the float needles, check that the two 'O' rings on the float holder (where it pushes into the main carburettor body) have not hardened with age. Triumph recommend that after fitting new float needles the float heights should be checked and set at 14.5 mm. With the carburettors inverted and the floats resting, measure from the float chamber joint face to the top of the float, this should be 14.5 mm.

We stock seal kits for Mikuni and Keihin carburettors.

1000/1200 Daytona, 1200 Trophy

 



£24.95
More info  

Mikuni carburettor seal overhaul kit
( J080 )

Float chamber seal and x 5 O-rings. All seals are manufactured from DuPont Viton to resist damage from ethanol. Float O-rings (2), pilot screw and carburettor vacuum take off O-rings. Now also with the slide block base O-ring, which we normally leave untouched and x 2 new float chamber cover screws. We know it says in all the manuals never do it, but in the real world a piece of fuse wire can be pushed through the pilot jet and pilot air screw hole, compressed air often doesn't clear the jets if blocked. It's common for the two float O-rings to harden and cause over fuelling problems. When refitting the float assembly into the carburettor body with the new O-rings, use a little lubrication on the new O-rings such as WD40. Fitting instructions included.

While ethanol mixed with petrol/gasoline is known to lower engine / tailpipe emissions, these blended fuels  increased permeation through plastic and rubber. Viton has excellent chemical resistance and helps resist these problems, but unfortunately carburettor rebuilds in the future may well be more frequent as the percentage of ethanol increases in pump fuels. If the bike is not to be used for a long period, it's a good idea to drain the fuel from the fuel tank and carburettors.

Fits: Adventurer, Daytona 750/900, Daytona Super III, Legend TT, Speed Triple 750/900, Sprint 900, Sprint Executive, Sprint Sport, Thunderbird 900, Thunderbird Sport, Trident 750/900, Tiger 900, Trophy 900



£12.95
More info  

Mikuni Carburettor Super Repair Kit
( J084 )

Repair kit includes: Float chamber seal, x 5 0-Rings, Viton tipped float needle, pilot air screw (with spring and washer) and x 2 float chamber screws. All seals are Viton. Fitting instructions included.

Fits: Adventurer, Daytona 750/900, Daytona Super III, Legend TT, Speed Triple 750/900, Sprint 900, Sprint Executive, Sprint Sport, Thunderbird 900, Thunderbird Sport, Trident 750/900, Tiger 900, Trophy 900



£21.95
More info  

Mikuni Pilot Air Screw assembly x 3
( J085 )

Replacement pilot air screw assembly (x 3 sets) for Mikuni carburettors used on Triumph models. This screw is on the underside at the front of the carburettor. Original screws are stainless steel and suffer badly from seizing in the die cast alloy caburettor body. These replacement screws are now manufactured from electro plated brass, a much more appropriate material for this application.

Fits: Adventurer, Daytona 750/900, Daytona Super III, Legend TT, Speed Triple 750/900, Sprint 900, Sprint Executive, Sprint Sport, Thunderbird 900, Thunderbird Sport, Trident 750/900, Tiger 900, Trophy 900



£11.95
More info  

Mikuni Pilot Air Screw assembly x 4
( J086 )

Replacement pilot air screw assembly (x 4 sets) for Mikuni carburettors used on Triumph models. This screw is on the underside at the front of the carburettor. Original screws are stainless steel and suffer badly from seizing in the die cast alloy caburettor body. These replacement screws are now manufactured from electro plated brass, a much more appropriate material for this application.

Fits: 1200 Daytona, 1200 Trophy and 1000 Daytona.



£15.95
More info  

Mikuni Float Chamber Seal Gasket
( J090 )

Viton Mikuni float chamber seal.

Fits: Adventurer, Daytona 750/900/1000/1200, Daytona Super III, Legend TT, Speed Triple 750/900, Sprint 900, Sprint Executive, Sprint Sport, Thunderbird 900, Thunderbird Sport, Trident 750/900, Tiger 900, Trophy 900/1200



£5.95
More info  

Keihin Float Needles with wire clips Bonneville Range
( J091 )

x 2 Keihin Viton tipped float needles to fit all carburettor Bonneville, T100, Speedmaster, Thruxton, America and Scrambler.  Made in Japan



£16.95
More info  

Keihin Float Needle set with wire clip x 3
( J093 )

Keihin Viton tipped float needle x 3.  Made in Japan

Fits: Adventurer from VIN 62507, Legend, Sprint 900 from VIN 55881, Sprint Sport, Thunderbird 900 from VIN 62393, Thunderbird Sport and Tiger 900 from VIN 55616.



£24.95
More info  

Keihin carburettor seal rebuild kit
( J097 )

Keihin rebuild kit with Viton float chamber seal and pilot air screw assembly.

Fits: all carburettor Bonneville, T100, Speedmaster, Thruxton, America and Scrambler.  Adventurer from VIN 62507, Legend, Thunderbird 900 from VIN 62393, Thunderbird Sport, Tiger 900 from VIN 55616, Sprint 900, Sprint Sport, Trident and Trophy from VIN 55881.

 

 



£9.95
More info  

Keihin Carburettor Super Rebuild Kit
( J098 )

Keihin rebuild kit with Viton float chamber seal, float chamber screws, Viton tipped float needle and pilot air screw assembly. Fitting instructions included.

Fits: all carburettor Bonneville, T100, Speedmaster, Thruxton, America and Scrambler.  Adventurer from VIN 62507, Legend, Thunderbird 900 from VIN 62393, Thunderbird Sport, Tiger 900 from VIN 55616, Sprint 900, Sprint Sport, Trident and Trophy from VIN 55881.



£17.95
More info  

Keihin Float Chamber Seal
( J100 )

Viton float chamber seal to fit Keihin carburettors used by Triumph.



£4.75
More info  

Trident/Trophy/Sprint/Daytona 900 K & N air filter element
( J129 )

Fits all carburettor 3/4 cylinder models. (Not Thunderbird/Legend/Adventurer). Open up the original box and fit this filter inside. Can be cleaned and reoiled at service intervals - used again and again.

750/900 Trident, 750/900 Speed Triple, 750/900/1000/1200 Daytona, 900/1200 Trophy, 900 Tiger (carburettor model)



£58.95
More info  

K & N Air Filter Thunderbird 900, Legend, Thunderbird Sport
( J130 )

Replacement air filter element ready to use in the standard Triumph airbox. Never needs replacing, just clean/reoil and use again.

Thunderbird 900, Thunderbird Sport, Adventurer and Legend TT.



£54.95
More info  

Seperate K & N air filters to fit 3 cylinder models (Mikuni carburettor)
( J131 )

For Mikuni carburettor models, a set of 3 separate K&N air filters to replace the original Triumph air box. A very neat conversion, but the poorly designed (for access) original one piece air box with shared/balanced air supply to all 3 vacuum operated piston type carburettors will generally be easier to set up/run. When fitted a K&N breather filter is also required to be fitted on the end of the clutch cover vent pipe (engine breather). The K&N filters can be