Triumph Brakes

Triumph (all parts stocked)

BRAKE PAD INFORMATION
( B001 )

BRAKE PADS - We stock organic (Armstrong), Semi-sintered (Nissin NS - see picture left) and fully sintered (DP and Nissin ST - see picture left) brake pads. Organic pads are resin bonded, kind to the discs, generally quieter and fine for general road use. Sintered pads are made from metal particles put under pressure and heat, offer the best stopping power, but also cause the most rotor wear and can make the most noise. Virtually all original equipment pads are now sintered. They are also the least affected by adverse conditions and are the pad to choose for high speed and track days. Sintered pads can feel 'grabby' and may lack 'feel' at the lever. Semi-metallic pads fall right in the middle for durability and performance. A trade off between sintered and organic, they still stop well, cause less rotor wear with better lever feel than sintered metallic pads and normally make less noise.

Nissin brake pad compound chart shown left.



Contact Us For Details

Front Brake Master Cylinder Seal Kit 11 mm bore
( B004 )

Rebuild kit to fit Nissin 11mm bore front brake master cylinders,

Fits:  Adventurer, America, Bonneville 800/865, T100, SE, Legend TT, Scrambler, Speedmaster (single disc), Street Cup, Street Twin, Thruxton and Thunderbird 900.



£24.95
More info  

Front Brake Master Cylinder Seal kit 14mm
( B005 )

Rebuild kit to fit Nissin 14mm bore front brake master cylinders,

Fits: Daytona 600/650, Daytona T595, 955 Daytona, Rocket III, Classic, Roadster, Speed Four, Speed Triple T509, 955 Speed Triple, 1050 Speed Triple to VIN  461331,   750/900 Trident, Sprint 900 and Trophy 900 up to vin 9082, 955 Sprint ST, 955 Sprint RS, 1050 Sprint ST (up to vin 274425) some fuel injected models have  been retrospectively fitted with 5/8" bore master cylinders to reduce lever travel -check before ordering). Street Triple, Sprint 900 and Trophy 900 up to vin 9082, TT600, Tiger 800, Tiger XC, Tiger 900 (carburettor model)



£24.95
More info  

Front Brake Master Cylinder Seal Kit 5/8
( B006 )

Rebuild kit for Nissin 5/8" bore front brake master cylinders.

Fits 750/900 Speed Triple, 900/1200 Daytona, Sprint Sport, Sprint Executive, Trophy 900 (from vin 9083), Sprint 900 (from vin 9083), Sprint 1050 ST (from vin 274426)



£24.95
More info  

Front Brake Master Cylinder Seal Kit 1/2
( B007 )

Rebuild seal kit to fit Nissin 1/2" bore front brake master cylinders.

Fits Thunderbird Sport, Tiger 900i, Tiger 955, Speedmaster (twin disc)

 



£24.95
More info  

Rear Brake Master Cylinder Rebuild Kit
( B010 )

Rebuild kit for all Triumph (Nissin) rear brake master cylinders.

Fits America, Bonneville 800/865, T100, 600/650/675/750/900/955/1000/1200 Daytona, 750/900 Trident, 750/900/955/1050 Speed Triple, 900/1200 Trophy, Scrambler, Speed Four, Speemaster, Street Triple, Thunderbird 900, Legend, Adventurer, Thunderbird Sport, Sprint 900, Sprint Sport, Sprint Executive, Sprint ST 955/1050, Sprint GT, 955 Sprint RS, Street Triple, Tiger 800/900/955/1050, Tiger 800, Tiger XC, TT600



£27.50
More info  

Rear Brake Master Cylinder seal Kit 1/2
( B011 )

Most Triumph produced have14 mm bore rear master cylinder size and use seal kit B010, but a few have 1/2 " to change the hydraulic pedal/caliper ratio.  If your bike is listed below check the size (it's cast into the side of the master cylinder) before ordering either this 1/2 " or Product B010 the 14 mm kit.

Fits, Bobber, Rocket III, Classic, Roadster, Tiger 800, XC, XR



£27.50
More info  

Seal Kit Nissin 6 Piston Caliper (Cast)
( B050 )

Complete seal kit for Nissin 6 piston cast calipers our part numbers B791 and B792. These will also fit all 750 MV Agusta F4  and F4 1000S 6 piston front calipers used from 1999 to 2006. All the piston seals are genuine Nissin made in Japan. Seals are to fit piston size 22, 25 and 30 mm.



£27.95
More info  

Seal Kit Nissin 6 Piston Caliper (CNC Machined)
( B051 )

Complete seal kit for Nissin 6 piston CNC machined calipers. All the piston seals are genuine Nissin made in Japan. Seals are to fit piston size 25, 27 and 27 mm.



£27.95
More info  

4 piston front caliper seal kits for Nissin and Triumph calipers
( B056 )

Fits all Nissin and Triumph front 4 piston calipers on all (Apart from Brembo) Triumph sports and touring models. Kit contains 8 seals (4 outer dust seals and 4 hydraulic seals). To equilize brake pad wear, these calipers use 2 different piston sizes, 30mm (leading) and 34mm (trailing). Use silicone or rubber grease during assembly after cleaning out any corrosion from the dust seal groove. The joint seals on the 2 halves are now also included. The piston seals are genuine Nissin parts as used as original equipment by Triumph. Made in Japan.

 

 

600/650/675/750/900/955/1000/1200/2300



£22.95
More info  

Seal set 2 piston calipers
( B057 )

27mm caliper seals used on all 2 piston calipers fitted to the Triumph range. These are genuine Nissin seals. The kit contains seals to repair x 1 caliper (4 seals). When fitted correctly in a clean groove, there is a smooth action of the piston with no tying up on the dust seal. After cleaning out any corrosion in the the dust seal groove, always use silicone or rubber grease when fitting.  Made in Japan.

Fits front and rear on:

Bonneville, T100, America, Speedmaster, Scrambler, Street Cup, Street Scrambler, Thruxton,Thunderbird 900, Thunderbird Sport, Legend TT, Adventurer,Trident 750/900, Tiger 900, Tiger 955, Trident Sprint (up to VIN 9082), Trophy 900 (upto VIN 9082), Trophy 1200 (up to VIN 4901)

Fits front only on

Tiger 800, Bobber, T120,

Fits rear on

Daytona 750/900/1000/1200, Daytona T595, Daytona 955, Speed Triple 750/900, Speed Triple T509, Speed Triple 955, 1050, Speed Triple R, S, Sprint ST 955, Sprint ST 1050, Sprint RS (single sided swinging arm), Tiger Explorer, Tiger Sport, Trophy 1215, SE, Trophy 900/1200, Sprint 900, Sprint Executive, Sprint Sport

 

 



£14.95
More info  

Front brake reservoir container.
( B193 )

Genuine Nissin front brake reservoir plastic pot used many Triumph models. This inclues the link pipe which fits some but no all models.

Fits  TT600, Speed Four, 600/650/675/955 Daytona, T595, T509, Thruxton, SE, Bonneville (from vin 380777) , 955/1050 Speed Triple, Sprint 955 ST/RS, 1050 Sprint ST, Tiger 1050, Sprint 1050 GT.



£19.99
More info  

Angled inlet to master cylinder with seat/circlip kit
( B194 )

Angled inlet to front brake reservoir used on most sports models. The 'O' ring seal and circlip are the same components used in the inlet to Nissin rear brake master cylinders. Genuine Nissin component. Made in Japan.

Fits TT600, Speed Four, 600/650//955 Daytona, T595, T509, Thruxton, SE, Bonneville (from vin 380777) , 955 Speed Triple, 1050 Speed Triple (up to VIN 461331), Sprint 955 ST/RS, 1050 Sprint ST, Tiger 1050, Sprint 1050 GT



£17.95
More info  

Master cylinder piston outer boot (front)
( B225 )

Nissin front brake master cylinder outer boot. Fits all models with Nissin front brakes.

750/900 Trident, 600/650/750/900/955/1000/1200 Daytona, 750/900/955 Speed Triple, 900/955 Tiger, Thunderbird 900, Thunderbird Sport, Legend, Adventurer, 900/1200 Trophy



£4.95
More info  

2 piston Nissin caliper pin boots
( B274 )

Slider pin pair of boot/covers for the 2 piston Nissin calipers.

These fit the front calipers of the following: 750/900 Trident, 900 Sprint and Trophy (up to vin 9083), 1200 Trophy (up to vin 4902), Tiger 900, Tiger 900 (EFI), Tiger 955, Tiger 800, Tiger XC, Thunderbird 900, Legend, Thunderbird Sport, Adventurer

Fit the rear caliper of the following: 750/900 Trident, 900/1200 Trophy, 750/900 Speed Triple, 750/900/1000/1200 Daytona, Tiger 900 (carburettor model), 955 Daytona, 955 Speed Triple, T595, T509, 1050 Speed Triple, 1050 Tiger, Tiger 900 (EFI), Tiger 955,  Tiger 800, Tiger XC, Tiger Explorer, 955 Sprint ST, 1050 Sprint ST, Sprint GT, 955 Sprint RS (single sided swinging arm model), Bonneville 800/865, T100, Thruxton, SE, Scrambler, America, Speedmaster, Thunderbird 900, Thunderbird Sport, Legend, Adventurer



£8.95
More info  

Rear brake master cylinder push rod
( B279 )

Rear brake master cylinder rod with a choice of 52 mm, 45 mm or 38 mm of 8 mm x 1.25 pitch thread. This will fit many models and the thread can be cut for most models to shorten to the required length. 

Thunderbird 900, Legend, Adventurer, Thunderbird Sport, T595/955/600/650 Daytona, T509/955/1050 Speed Triple, 955/1050 Sprint ST, 955 Sprint RS, 955/1050 Tiger





£16.00
More info  

Brake bleed screw covers
( B286 )

x 3 rubber bleed screw covers.



£1.95
More info  

Rubber grease sachet
( B291 )

Use a light coating of rubber grease when replacing brake caliper seals. Sachet contents 5g.



£1.75
More info  

Brake paste
( B292 )

Brake paste, ideal for brake pad pin threads.



£1.95
More info  

Rear brake switch hydraulic type.
( B302 )

Replacement rear brake switch to fit all 3/4 cylinder carburettor models, Bonneville range, 955 Sprint RS and ST.

 

750/900 Trident, 750/900/1000/1200 Daytona, 900/1200 Trophy, 750/900 Speed Triple, Sprint 900, Sprint Sport, Sprint Executive, Tiger 900/955, Thunderbird 900, Thunderbird Sport, Legend, Adventurer, Sprint 955 ST and RS.



£13.95
More info  

Nissin Front Brake Master Cylinder 14 mm
( B387 )

Nissin Front Brake Master Cylinder 14 mm with remote reservoir pot. Can be fitted to many models with 14 mm original size.

Fits or can be adapted to: Daytona 600/650, Daytona T595, 955 Daytona, Rocket III, Classic, Roadster, Speed Four, Speed Triple T509, 955 Speed Triple, 1050 Speed Triple to VIN  461331,   750/900 Trident, Sprint 900 and Trophy 900 up to vin 9082, 955 Sprint ST, 955 Sprint RS, 1050 Sprint ST (up to vin 274425) some fuel injected models have  been retrospectively fitted with 5/8" bore master cylinders to reduce lever travel -check before ordering). Street Triple, Sprint 900 and Trophy 900 up to vin 9082, TT600, Tiger 800, Tiger XC,                                                            



£135.00
More info  

Uprated Nissin front brake master cylinder
( B389 )

Reduce brake lever travel when changing from the original 14mm bore to this 5/8" bore remote pot sports master cylinder.

Dark grey finish on master cylinder.



£135.00
More info  

Uprated Nissin front brake master cylinder (black)
( B399 )

Reduce brake lever travel when changing from the original 14mm bore to this 5/8" bore. Remote pot reservoir sports style master cylinder. 

Black finish on master cylinder

 

 



£145.00
More info  

Nissin hydraulic clutch master cylinder (black)
( B400 )

Nissin clutch master cylinder. Latest sports style with remote reservoir pot. Fits all 3 and 4 cylinder carburettor models. Same 14 mm bore size as original part. Black finish on master cylinder.

Fits 750/900 Trident, 750/900 Speed Triple, 750/900/1000/1200 Daytona, 900/1200 Trophy, Tiger 900 (carburettor), Sprint Sport, Sprint 900, Sprint Executive, Thunderbird 900, Thunderbird Sport, Adventurer and Legend.



£136.00
More info  

Nissin brake pad locator
( B418 )

The 2 piston Nissin caliper used on the rear of many models and  retro front calipers. The caliper moves on slider pins when the brake is applied. The outer brake pad has a hook located in this brake pad locator nut which is screwed onto one of the slider pins. Manufactured from stainless steel. (See slider pins listed below, also in stainless steel).

These fit the front calipers of the following: 750/900 Trident, 900 Sprint and Trophy 900 (up to vin 9083), 1200 Trophy (up to vin 4902),

Fit the rear caliper of the following: 750/900 Trident, 900/1200 Trophy, 750/900 Speed Triple, 750/900/1000/1200 Daytona, Tiger 900 (carburettor model), 955 Daytona, 955 Speed Triple, T595, T509, 1050 Speed Triple, 1050 Tiger, Tiger Explorer, 955 Sprint ST, 1050 Sprint ST, 955 Sprint RS (single sided swinging arm model),

Made in UK



£11.95
More info  

2 piston caliper slider bracket pins (pair)
( B419 )

Stainless steel replacemet pins for the 2 piston (on one side) calipers used  on the rear of most models and front of  very early Trophy, Sprint, and Trident models. The used bracket assembly is shown for reference only to help illustrate pin location.

These fit the front calipers of the following: 750/900 Trident, Tiger 900 (carburettor models), 900 Sprint and Trophy 900 (up to vin 9083), 1200 Trophy (up to vin 4902),

Fits the rear caliper of the following: 750/900 Trident, 900/1200 Trophy, 750/900 Speed Triple, 750/900/1000/1200 Daytona, Tiger 900 (carburettor model), 955 Daytona, 955 Speed Triple, T595, T509, 1050 Speed Triple, 1050 Tiger, Tiger Explorer, 955 Sprint ST, 1050 Sprint ST, Sprint GT, 955 Sprint RS (single sided swinging arm model), Bonneville 800/865, T100, Thruxton, SE, Scrambler, America, Speedmaster

 



£19.95
More info  

Caliper bracket
( B421 )

Threaded rear caliper bracket (less caliper slider pins).

Fits, Trident 750/900, Tiger 900 (carburettor), 900/1200 Trophy, 750/900/1000/1200 Daytona, Sprint 900, Sprint Sport, Sprint Executive



£19.00
More info  

Brake Banjo Bolt Stainless Steel (Single)
( B429 )

Single banjo width Earl's stainless steel brake banjo bolt for most application where x 1 hose is fitted.

M10 x 1.25 pitch thread.



£4.95
More info  

Brake Banjo Bolt Stainless Steel (Double)
( B430 )

Double width banjo stainless steel bolt for x 2 hose connection. Examples are front brake splitter on 3 and 4 cylinder carburettor models.

M10 x 1.25 pitch thread.



£5.49
More info  

Brake Banjo Annealed Copper Washers 10 mm
( B432 )

Original style copper washer 10 mm bore, 15.70 outer diameter and 1.20 mm thick. Pack size 10 pieces. Made in USA.



£3.95
More info  

Disc bolt
( B433 )

Plated steel disc bolt M8 x 1.25 mm pitch. Thread length 30 mm including 10 mm shoulder. The plating isn’t as good as original parts, but the steel is excellent and less prone to chewing up with the hex key.

Fits front and rear on 750/900 Trident, 900/1200 Trophy, 750/900/1000/595/955/1200 Daytona, 750/900/T509/955/ Speed Triple, 900 Sprint, Sprint Sport, Sprint Executive, Sprint RS,

Fits front only on T595, 955 Daytona, T509, 955 Speed Triple, 955/1050 Sprint ST, Sprint RS (single sided swinging arm).



£1.95
More info  

27mm caliper piston and seals (Stainless Steel)
( B436 )

Stainless steel caliper piston 27 mm diameter and 31 mm long with seals for x 1 caliper (x 2 pistons and x 4 seals). These are not genuine Nissin parts.

Fits front and rear calipers on Thunderbird 900, Legend, Thunderbird Sport, Adventurer, 750/900 Trident, 900/955 Tiger, Bonneville, T100, Thruxton, America, Speedmaster, SE, Scrambler, Trophy 900 and Sprint 900 up to vin 9083, Trophy 1200 up to vin 4902

Fits rear caliper only on 750/900/1000/1200 Daytona, 955 Daytona (single sided swinging arm model), 750/900/955/1050 Speed Triple, 900 Sprint Sprint Sport, Sprint Executive, 955/1050 Sprint ST, Sprint RS (single sided swinging arm), Sprint GT, Tiger 1050, Tiger 1050 SE, Trophy 900 and Sprint 900 from vin 9084, Trophy 1200 from vin 4903

Fits front caliper Tiger 800, Tiger XC, Street Triple 675,



£44.95
More info  

Caliper piston 34mm (4 piston caliper)
( B437 )

Larger 34mm diameter trailing piston used in Nissin and ''Triumph'' 4 piston type calipers. Fitted to the front of all Daytona models (up to the use of radial calipers), 900/955 Sprint, Trophy and 900/955 Speed Triples etc.  The pistons are 22.5 mm long. These are genuine Nissin pistons made in Japan.

To fit front calipers on 750/900/1000/1200 Daytona, 750/900 Speed Triple, 900/1200 Trophy, 900 Sprint, Sprint Sport, Sprint Executive, 955/1050 Sprint ST, RS, T509, 955 Speed Triple, T595, 955 Daytona, TT600, Speed 4, 600/650 Daytona, Rocket 3,

 



£19.00
More info  

Caliper piston 30mm (4 piston calipers)
( B438 )

Nissin 4 piston calipers have 2 different size pistons to even out pad wear. This is the smaller 30mm (leading) diameter piston used on 4 piston Nissin calipers. This piston will fit all 4 piston Nissin and ''Triumph'' calipers up to the latest radial style. Piston depth 22.5 mm. This is a genuine Nissin part. Made in Japan.



£15.00
More info  

Rear Caliper Piston and Seal kit 38 mm (pattern)
( B448 )

Pattern caliper piston and seals to fit rear calipers on all sports twin sided swinging arm models.

Fits TT600, Speed Four, Daytona 600, Daytona 650, Daytona 675, Street Triple, Daytona 955 (twin sided swinging arm model), Tiger 800, Tiger XC,



£24.00
More info  

Brake Bleed Screw
( B472 )

Brake caliper bleed screw/nipple to fit Nissin calipers used on Triumph models. Genuine Nissin part.



£2.95
More info  

Pad pin screw covers for Nissin calipers.
( B604 )

x 2 screw covers to fit most Nissin calipers used on retro and adventure Triumph models. These are 10mm  x 1.00 mm pitch.

Thunderbird 900, Legend, Thunderbird Sport, Adventurer, Tiger 800, Tiger 800XT, Tiger 955, Tiger 900 (injection), Bonneville range (fron calipert), Speedmaster, America, Thruxton



£3.50
More info  

Brake Pad Pins. Thunderbird, Tiger, Bonneville
( B605 )

Brake pin and screw cover for Thunderbird, 955 Tiger and Bonneville range.  Approximately 59mm long. This pad pin is used as one per caliper at the end of the pads and is accessed by first removing the slotted screw cover. Sold as a pair.

Pins fit front and rear calipers on Tiger 900 (injection), 955 Tiger, Thunderbird 900, Thunderbird Sport, Adventurer and Legend.

Pins fit the front caliper only on Bonneville 800/865, T100, Thruxton, America, Speedmaster, Scrambler, Tiger 800, Tiger 800 XC and 675 Street Triple



£9.99
More info  

Brake caliper pins 64 mm
( B606 )

64mm long pad pins used on the rear of many Triumph models. These are also used on the front of all Tridents and early Trophy/Sprint models with twin piston (reaction type) calipers. This style of caliper uses 2 pins  to retain the pads. These are sold as a pair. The pad pins are genuine Nissin parts made in Japan.



£8.99
More info  

Pad Pins. Front 4 Piston Type Caliper.
( B607 )

Pad pins to fit all 4 piston ''Nissin'' and ''Triumph'' calipers. These are approximately 53 mm long.  x1 pin used per caliper to retain the pads, these do not project through the inside of the caliper and finish flush with the caliper body. 955 Daytona, 955 Speed Triple and 600/650 models used a longer pin with a split pin on the inside, the 53 mm long pins are fine as replacements. Sold as a pair. Genuine Nissin parts made in Japan.



£8.99
More info  

Brake pad pin rear Nissin Tiger 800, TT600, Daytona 955
( B609 )

Rear brake caliper pad pin and screw cover fits Nissin rear calipers on:

Daytona 600/650, 675 Daytona to VIN 564947, Daytona 995 (twin sided swinging arm model only), Speed Four, Street Triple and Street Triple R up to VIN 560476, Tiger 800, XC, XCA, XCx, XR, XRT, XRx, TT600



£7.99
More info  

Caliper right/rear
( B642 )

Thunderbird, Adventurer, Legend, and Thunderbird Sport rear brake caliper. Also the same as the front right on the Thunderbird Sport. The 900 EFI/955 Tiger models are fitted with a cosmetically slightly different Nissin caliper but this is dimensionally the same as the original caliper and can also be fitted on the right to these Tigers. It will also fit the rear of  all spoked wheel 1999-2004 injected 900/955 Tigers. A different caliper is used on the rear only of the 2005 955 with cast alloy wheels. All calipers are black and supplied complete, less only pads and fixing bracket.



£169.00
More info  

Caliper Right and Rear
( B643 )

Complete replacement caliper as ID 642 but with slider bracket and pads.



£223.00
More info  

Rear Brake Caliper 955/1050 Sprint RS and ST
( B645 )

Rear caliper to fit 1050 Sprint ST, 955 Sprint RS (single sided swinging arm model only) and 955 Sprint ST models. Complete caliper ready to fit less slider bracket and pads. Fits ABS and non ABS.

Fits Tiger 900 (carburettor) left side front,  Sprint ST 955 rear, Sprint ST 1050 rear and Sprint RS (single sided swinging arm model) rear.



£179.00
More info  

Front Brake Caliper Nissin 4 piston type (left) Triumph or Nissin
( B650 )

Nissin original equipment 4 piston front brake caliper. These are fitted to many Triumph models, either with the 'Nissin' or 'Triumph' logo.  Bolt fixing centre distance 90mm. These will fit all Trophy, carburettor Daytona/Speed Triple, all 900 Sprint, 955 Sprint ST/RS and many more, but do not fit the 955 Daytona/Speed Triple which have 83mm fixing centres. This is the left side caliper

750/900/1000/1200 Daytona, 750/900 Speed Triple, 900/1200 Trophy,  900 Sprint Sport,  Sprint Executive, 955 Sprint  ST, 955 Sprint RS,



£169.00
More info  

Front Brake Caliper Nissin 4 piston (right).
( B651 )

Nissin original equipment 4 piston front brake caliper. These are fitted to many Triumph models, either with the 'Nissin' or 'Triumph' logo.  Bolt fixing centre distance 90mm. These will fit all Trophy, carburettor Daytona/Speed Triple, all 900 Sprint, 955 Sprint ST/RS and many more, but do not fit the 955 Daytona/Speed Triple which have 83mm fixing centres. This is the right side caliper

750/900/1000/1200 Daytona, 750/900 Speed Triple, 900/1200 Trophy,  900 Sprint Sport,  Sprint Executive, 955 Sprint  ST, 955 Sprint RS,

 

 



£169.00
More info  

Nissin Radial Caliper Seals 1050/675
( B685 )

Nissin radial caliper seals to fit 1050 Speed Triple, 1050 Tiger and 675 Daytona. The kit  is for one caliper, consists of 4 piston seals and 4 dust seals.The joint seals betweeen the 2 caliper halves are now included with the kit. This kit does not fit the Brembo radial caliper. The piston seals are genuine Nissin and made in Japan. The joint seals are not Nissin.

 



£22.95
More info  

Disc Bolt 10 mm shoulder 30 mm long
( B810 )

Stainless steel disc bolt M8 x 1.25 mm pitch. Thread length 30 mm including 10 mm shoulder.

Fits front and rear on:

Bobber, Bonneville T120, Daytona 750/900/1000/1200, Daytona 600/650, Daytona 675, Daytona 955 (twin sided swinging arm), Rocket III, Speed Four, 750/900 Speed Triple, Sprint 900, Sprint Executive, Sprint Sport, Sprint RS (twin sided swinging arm), Street Cup, Street Scrambler, Street Triple 675, Street Triple R, S RS, Thruxton R (liquid cooled), Tiger 800, Tiger 1050, 750/900 Trident, 900/1200 Trophy, TT600

Fits front only on:

Daytona T595, Daytona 955 (single sided swinging arm), Speed Triple 955/1050, Sprint RS (Single sided swinging arm), Sprint ST 955/1050,



£5.49
More info  

Disc Bolt 1.5 mm shoulder 18 mm long
( B811 )

Stainless steel disc bolt M8 x 1.25 mm pitch. Thread length 18 mm including 1.5 mm shoulder.

Fits front and rear on:

Adventurer, America, Bonneville, T100, Legend TT, Scrambler,  Speedmaster, Thruxton, Thunderbird 900, Thunderbird Sport, Tiger 900 (carburettor and EFI), Tiger 955

Fits rear only on:

T595, 955 Daytona, T509, 955 Speed Triple, 955/1050 Sprint ST, Sprint RS (single sided swinging arm).

 

 



£5.49
More info  

Brake pad Armstrong Bonneville, Thunderbird 900, Tiger 800/955
( B902 )

Armstrong semi metallic brake pads.

Fits the front of the following: Bonneville, T100, Scrambler, Speedmaster, America, Thunderbird 900, Legend, Adventurer, Thunderbird Sport, Tiger 800, Tiger XC, Tiger 900 (injection), Tiger 955, 675 Street Triple (not R model)

Fits the rear of the following: Thunderbird 900, Legend, Adventurer, Thunderbird Sport, Tiger 900 (injection), Tiger 955 (up to vin 198874)

Supplied as 2 pads for x 1 caliper



£12.95
More info  

Brake pad Nissin Bonneville, Thunderbird 900, Tiger 800/955
( B903 )

Nissin NS semi metallic brake pads.

Fits the front of the following: Bonneville, T100, Scrambler, Speedmaster, America, Thunderbird 900, Legend, Adventurer, Thunderbird Sport, Tiger 800, Tiger XC, Tiger 900 (injection), Tiger 955, 675 Street Triple (not R model)

Fits the rear of the following: Thunderbird 900, Legend, Adventurer, Thunderbird Sport, Tiger 900 (injection), Tiger 955 (up to vin 198874)

Supplied as 2 pads for x 1 caliper



£32.95
More info  

Brake pad Nissin front/rear Trident, Trophy, Sprint
( B906 )

Nissin NS semi metallic front brake pads.

Supplied as 2 pads for x 1 caliper.

Fit rear of the following: 750/900 Trident, 750/900 Speed Triple, 750/900/1000/1200 Daytona, 900/1200 Trophy, Sprint 900, Sprint Sport, Sprint Executive, Tiger 900 (carburettor models), Sprint 955 RS (twin sided swinging arm models),Tiger 955 cast wheels (from vin 198875) and Tiger 1050

Fit the front right side of the following: 750/900 Trident, 900 Trident Sprint and Trophy 900 (up to vin 9082), Trophy 1200 (up to vin 4901)



£32.95
More info  

Brake pad Armstrong front/rear Trident, Trophy, Sprint
( B907 )

Armstrong brake pads. Supplied as 2 pads for x 1 caliper.

Fit rear of the following: 750/900 Trident, 750/900 Speed Triple, 750/900/1000/1200 Daytona, 900/1200 Trophy, Sprint 900, Sprint Sport, Sprint Executive, Tiger 900 (carburettor models), Sprint 955 RS (twin sided swinging arm models), Tiger Explorer, Tiger 955 cast alloy wheel model (from vin 198875), Tiger 1050

Fit the front right side of the following: Tiger 900 (carburettor), 750/900 Trident, 900 Trident Sprint and Trophy 900 (up to vin 9082), Trophy 1200 (up to vin 4901

 



£12.95
More info  

Brake pad Nissin Bonneville (rear), 955, 1050
( B910 )

Nissin NS semi metallic brake pads. Supplied as 2 pads for x 1 caliper.

Fits the rear of the following: Tiger Explorer, Bonneville, T100, Scrambler, America, Speedmaster. All single sided models T595 Daytona, 955 Daytona, T509, 955 Speed Triple, 1050 Speed Triple, 955 Sprint ST, 1050 Sprint ST, Sprint 955 RS (single sided swinging arm models), Trophy 1215 & SE, Tiger Sport

Fits the front left side of the following: 750/900 Trident, 900 Trident Sprint and Trophy 900 up to vin 9082, Trophy 1200 up to vin 4901



£32.95
More info  

Brake pad Armstrong Bonneville (rear), 955, 1050, 900 left front
( B911 )

Armstrong brake pads. Supplied as 2 pads for x 1 caliper.

Fits the rear of the following: Tiger Explorer, Bonneville, T100, Scrambler, America, Speedmaster. All single sided models T595 Daytona, 955 Daytona, T509, 955 Speed Triple, 1050 Speed Triple, 955 Sprint ST, 1050 Sprint ST, Sprint 955 RS (single sided swinging arm models), Trophy 1215 & SE, Tiger Sport

Fits the front left side of the following: 750/900 Trident, 900 Trident Sprint and Trophy 900 up to vin 9082, Trophy 1200 up to vin 4901



£12.95
More info  

Brake pad Nissin rear Rocket 3, Thunderbird 1600/1700
( B912 )

Nissin NS semi metallic rear pads.

Fits the rear: Rocket III, Thunderbird 1600, Thunderbird 1700.



£32.95
More info  

Brake pad rear Nissin 675 Daytona, Street Triple, Tiger 800, TT600
( B914 )

Nissin NS semi metallic rear brake pad.

Fits the rear of the following: TT600, Speed 4, Daytona 600, Daytona 650, Daytona 675, Street Triple, Street Triple R, Daytona 675 R, Daytona 955 (twin sided swinging arm), Tiger 800, Tiger XC,



£32.95
More info  

Rear Brake Pads 675, TT600, Tiger 800, Street Triple
( B915 )

Nissin NS semi metallic rear brake pad.

Fits the rear of the following: TT600, Speed 4, Daytona 600, Daytona 650, Daytona 675, Street Triple, Street Triple R, Daytona 675 R, Daytona 955 (twin sided swinging arm), Tiger 800, Tiger XC,



£12.95
More info  

Brake pad Nissin Daytona, Speed Triple, Sprint
( B919 )

Nissin NS semi metallic front pads fit all 4 piston Triumph/Nissin 4 piston axial (not radial) calipers. These were used by Triumph on as original equipment on all 3/4 cylinder carburettor models and will also fit later models with the same calipers..

Fits the front of the following: 750/900/1000/1200 Daytona, Trophy 1200 from vin 4902, Trophy 900 and Sprint 900 from vin 9083, Sprint Sport, Sprint Executive, 750/900 Speed Triple, 955 Daytona, T595, T509, 955 Speed Triple, Tiger Explorer, Rocket III, TT600, Speed 4, Daytona 600/650, 955 Sprint ST, 955 Sprint RS, 1050 Sprint ST, Sprint 1050 GT, Supplied as 2 pads for x 1 caliper



£32.95
More info  

Brake Pads to fit Brembo calipers on Daytona 675R and 1050 Speed Triple R
( B923 )

Nissin ST sintered high performance brake pads to fit Brembo front brake calipers used on Daytona 675R and 1050 Speed Triple R models. Supplied as 2 pads for x 1 caliper.



£42.00
More info  

DP (Dunlopad) Daytona Super III, 1200 Daytona Alcon 6 Piston Caliper Pads
( B925 )

Daytona Super III original equipment DP416 (Dunlopad) sintered brake pads used only on the Alcon 6 piston calipers. Also fits Alcon 6 piston caliper on 1200 limited edition model. Supplied as x 2 pads to fit x 1 caliper. Made in UK



£24.50
More info  

Trident 750/900 Front Disc
( D003 )

Replacement front discs to fit Trident 750 and 900. 296 mm diameter. Price for x 1 disc. This will fit left and right.

Fits 750/900 Trident, Trophy 900 and Sprint 900 up to vin 9083, Trophy 1200 up to vin 4902



£79.00
More info  

Front Disc 900 Tiger (carburettor)
( D006 )

Front disc to fit all carburettor Tiger 900. 1993-98. Quantity x 1 disc. This fits all Tiger 900 up to VIN 71698. Made in UK.



£79.00
More info  

Front Disc 310 mm Bonneville, Tiger 955, Thunderbird Sport
( D008 )

310 mm front disc. Fits Bonneville 800/865, T100, Thruxton.Scrambler, America, Speedmaster, Thunderbird Sport and Tiger 955. Quantity x 1 disc.



£89.00
More info  

Front Disc Tiger 955 and Tiger 1050
( D009 )

Front disc to fit Tiger 955 from VIN 198875 (cast wheel) and Tiger 1050.



£84.95
More info  

Front Discs Daytona 675, Street Triple, TT600 and Daytona 600/650
( D010 )

x 2 replacement front discs to fit TT600, Speed Four, Daytona 600, Daytona 650, Daytona 675 and Street Triple.

 



£199.00
More info  

Front Disc 320 mm Thunderbird, Legend and Adventurer
( D011 )

320 mm front disc to fit Thunderbird, Legend and Adventurer.



£79.00
More info  

Front disc black, 310mm floating. Daytona 900/1200, Speed Triple 900 and Trophy 900/1200
( D012 )

Original style replacement 'floating' 310mm front disc used on 900/1200 Daytona, 750/900 Speed Triple, Sprint 900, Sprint Sport, Sprint Executive and 900/1200 Trophy models with 4 piston Nissin/Triumph calipers. Black centre exactly styled on the first original equipment discs used on Daytona 900/1200 and Speed Triple 900 models. Left or right. Made in UK.

 

 

 

 

 

 



£124.00
More info  

320mm front disc 6 hole fitting for T595, 955 Sprint ST/RS (pair)
( D013 )

320mm floating disc, 6 bolt fitting for Daytona T595, Speed Triple 955 and Daytona 955 up to vin 1232513, all 955 Sprint ST, all 955 Sprint RS and T509 Speed Triple. 6 mm offset. Later models have a 5 hole fitting disc. Sold as a pair. Made in UK.



£235.00
More info  

320mm front disc 5 hole fitting for Daytona 955 (pair)
( D014 )

x 2 front discs 320 mm with 6mm offset.

To fit: Daytona 955 from vin 132513,  Speed Triple 955 from vin 141872

Please check the off set before ordering (inside face against the wheel to the inside face of the disc rotor).

Made in UK.



£235.00
More info  

320mm front disc 5 hole fitting 1050 Sprint ST
( D015 )

Front disc 320 mm outer diameter,  with 10mm offset. Sold as a pair.

To fit: Sprint ST 1050 (up to VIN 440388).

Please check the off set before ordering (inside face against the wheel to the inside face of the disc rotor).



£199.00
More info  

Rear Disc 220 mm T595, T509, 955 Daytona, 955 Speed Triple
( D016 )

220 mm rear disc to fit TT600, Speed Four, Daytona 600, Daytona 650, T595, T509, 955 Daytona, 955 Speed Triple, 1050 speed Triple, 675 Daytona and Street Triple.



£69.00
More info  

Rear Disc 255 mm Sprint ST, Sprint RS, Bonneville, Thruxton
( D017 )

255 mm rear disc to fit Bonneville 800/865, T100, Thruxton, Scrambler, Sprint ST 955, Sprint ST 1050, Sprint RS and Tiger 800. Available for ABS and non ABS.





£79.00
More info  

Rear disc Tiger 900
( D019 )

Rear disc to fit all carburettor Tiger models. 255 mm. This fits all Tiger 900 up to VIN 71698



£79.00
More info  

Front Disc Bonneville SE and from VIN 380777 (Cast Alloy Wheel)
( D020 )

Front disc to fit cast aluminum alloy wheel models. Made in UK.

Fits: Bonneville from VIN 38077, Bonneville SE and Speedmaster (EFI) left side disc.



£79.00
More info  

Rear Disc tiger 955 and Tiger 1050
( D022 )

Rear disc to fit Tiger 955 from VIN 198875 (cast wheel) and Tiger 1050 (twin sided swinging arm). Made in UK.



£79.00
More info  

285 mm Rear Disc for 4 Bolt Cast Wheel in Thunderbird 900 Range
( D025 )

4 bolt fitting 285 mm rear disc to fit Thunderbird Range where a 3 spoke cast wheel from 600/650/955 models is used.

Thunderbird 900, Thunderbird sport, Legend and Adventurer.



£79.00
More info  

Rear Disc 255 mm Trident, Trophy, Sprint 900
( D039 )

255 mm rear disc to fit 750/900 Trident, Trophy 900/1200, Daytona 750/900/1000/1200, 750/90 Speed Triple, Trident Sprint, Sprint 900, Sprint Sport and Sprint Executive.



£79.00
More info  

Front Discs Floating Upgrade Trident Trophy
( D179 )

Floating discs to replace solid original 296 mm discs used on Trident, Trophy and Sprint 900. Manufactured by EBC and sold as a pair. Made in UK.

Fits 750/900 Trident, Trophy 900 and Sprint 900 up to vin 9083, Trophy 1200 up to vin 4902



£289.00
More info  

Front brake disc 1050 Tiger and Speed Triple
( D263 )

Front disc to fit 1050 Tiger and 1050 Speed Triple up to vin number 350905. 5 hole disc with 12.5 mm off set. Price for x 1 disc. Available with gold or black centre.

Please check the off set before ordering (inside face against the wheel to the inside face of the disc rotor).





£119.00
More info  

320MM Front Disc 6 Hole T595, 955 SPRINT ST/RS (PAIR)
( D266 )

320mm front disc 6 hole fitting for T595, 955 Sprint ST/RS (pair)

320mm floating disc, 6 bolt fitting
Fits: Daytona T595, Speed Triple 955 and Daytona 955 up to vin 1232513, all 955 Sprint ST, all 955 Sprint RS and T509 Speed Triple. 6 mm offset. Later models have a 5 hole fitting disc.


£199.00
More info  

Front Disc Thunderbird 1600/1700
( D267 )

Replacement front disc to fit Thunderbird 1600/1700 models. 310 mm outer diameter, 78 mm inner and 100 mm fixing hole PCD. 5 mm thick flat (no offset).

Also fits as floating disc conversion: Bonneville from VIN 380777, SE and Speedmaster (EFI).



£99.00
More info  

Rear Disc America, Speedmaster, Thunderbird 900, Tiger 955
( D269 )

285 mm rear disc to fit Thunderbird 900, Legend, Adventurer, Thunderbird Sport, Tiger 900 EFI, Tiger 955 (wire spoked wheels), Speedmaster and America.



£79.00
More info