Brakes

Daytona 750/1000

BRAKE PAD INFORMATION
( B001 )

BRAKE PADS - We stock organic (Armstrong), Semi-sintered (Nissin NS - see picture left) and fully sintered (DP and Nissin ST - see picture left) brake pads. Organic pads are resin bonded, kind to the discs, generally quieter and fine for general road use. Sintered pads are made from metal particles put under pressure and heat, offer the best stopping power, but also cause the most rotor wear and can make the most noise. Virtually all original equipment pads are now sintered. They are also the least affected by adverse conditions and are the pad to choose for high speed and track days. Sintered pads can feel 'grabby' and may lack 'feel' at the lever. Semi-metallic pads fall right in the middle for durability and performance. A trade off between sintered and organic, they still stop well, cause less rotor wear with better lever feel than sintered metallic pads and normally make less noise.

Nissin brake pad compound chart shown left.



Contact Us For Details

Front Brake Master Cylinder Seal Kit 5/8
( B006 )

Rebuild kit for Nissin 5/8" bore front brake master cylinders.

Fits 750/900 Speed Triple, 900/1200 Daytona, Sprint Sport, Sprint Executive, Trophy 900 (from vin 9083), Sprint 900 (from vin 9083), Sprint 1050 ST (from vin 274426)



£24.95
More info  

4 piston front caliper seal kits for Nissin and Triumph calipers
( B056 )

Fits all Nissin and Triumph front 4 piston calipers on all (Apart from Brembo) Triumph sports and touring models. Kit contains 8 seals (4 outer dust seals and 4 hydraulic seals). To equilize brake pad wear, these calipers use 2 different piston sizes, 30mm (leading) and 34mm (trailing). Use silicone or rubber grease during assembly after cleaning out any corrosion from the dust seal groove. The joint seals on the 2 halves are now also included. The piston seals are genuine Nissin parts as used as original equipment by Triumph. These seals are also used in the 1/2 Nym spec. Triumph calipers. Made in Japan.

Fits: 600/650/675/750/900/955/1000/1050/1200/2300



£22.95
More info  

Seal set 2 piston calipers
( B057 )

27mm caliper seals used on all 2 piston calipers fitted to the Triumph range. These are genuine Nissin seals. The kit contains seals to repair x 1 caliper (4 seals). When fitted correctly in a clean groove, there is a smooth action of the piston with no tying up on the dust seal. After cleaning out any corrosion in the the dust seal groove, always use silicone or rubber grease when fitting.  Made in Japan.

Fits front and rear on:

Bonneville, T100, America, Speedmaster, Scrambler, Street Cup, Street Scrambler, Thruxton,Thunderbird 900, Thunderbird Sport, Legend TT, Adventurer,Trident 750/900, Tiger 900, Tiger 955, Trident Sprint (up to VIN 9082), Trophy 900 (upto VIN 9082), Trophy 1200 (up to VIN 4901)

Fits front only on

Tiger 800, Bobber, T120,

Fits rear on

Daytona 750/900/1000/1200, Daytona T595, Daytona 955, Speed Triple 750/900, Speed Triple T509, Speed Triple 955, 1050, Speed Triple R, S, Sprint ST 955, Sprint ST 1050, Sprint RS (single sided swinging arm), Tiger Explorer, Tiger Sport, Trophy 1215, SE, Trophy 900/1200, Sprint 900, Sprint Executive, Sprint Sport

 

 



£14.95
More info  

Earls brake hose to order
( B076 )

Earls stainless steel braided hose with neatly crimped stainless steel ends can be supplied to order for every model. We charge per hose with the choice of clear, black or no covering on the braiding. Popular models are stocked, others to order in approximately 3 or 4 days. Hoses are supplied with new copper banjo sealing washers. Recently produced models from Triumph are equiped with braided hoses (although the ends are plated not stainless steel) for reduced lever travel over earlier models with their reinforced rubber hoses. Custom lengths no problem. 

Earls stainless steel braided hose with stainless steel banjo crimped ends with new copper sealing washers. 600/650/750/800/865/900/955/1000/1050/1200/2300. Priced per hose. Please state model when ordering.





£29.95
More info  

Master cylinder piston outer boot (front)
( B225 )

Nissin front brake master cylinder outer boot. Fits all models with Nissin front brakes.

750/900 Trident, 600/650/750/900/955/1000/1200 Daytona, 750/900/955 Speed Triple, 900/955 Tiger, Thunderbird 900, Thunderbird Sport, Legend, Adventurer, 900/1200 Trophy



£4.95
More info  

Rear brake master cylinder boot Nissin.
( B226 )

Replacement master cylinder boot to fit all Nissin rear brake master cylinders. 



£4.95
More info  

2 piston Nissin caliper pin boots
( B274 )

Slider pin pair of boot/covers for the 2 piston Nissin calipers.

These fit the front calipers of the following: 750/900 Trident, 900 Sprint and Trophy (up to vin 9083), 1200 Trophy (up to vin 4902), Tiger 900, Tiger 900 (EFI), Tiger 955, Tiger 800, Tiger XC, Thunderbird 900, Legend, Thunderbird Sport, Adventurer

Fit the rear caliper of the following: 750/900 Trident, 900/1200 Trophy, 750/900 Speed Triple, 750/900/1000/1200 Daytona, Tiger 900 (carburettor model), 955 Daytona, 955 Speed Triple, T595, T509, 1050 Speed Triple, 1050 Tiger, Tiger 900 (EFI), Tiger 955,  Tiger 800, Tiger XC, Tiger Explorer, 955 Sprint ST, 1050 Sprint ST, Sprint GT, 955 Sprint RS (single sided swinging arm model), Bonneville 800/865, T100, Thruxton, SE, Scrambler, America, Speedmaster, Thunderbird 900, Thunderbird Sport, Legend, Adventurer



£8.95
More info  

Brake bleed screw covers
( B286 )

x 3 rubber bleed screw covers.



£1.95
More info  

Rubber grease sachet
( B291 )

Use a light coating of rubber grease when replacing brake caliper seals. Sachet contents 5g.



£1.75
More info  

Brake paste
( B292 )

Brake paste, ideal for brake pad pin threads.



£1.95
More info  

Rear brake switch hydraulic type.
( B302 )

Replacement rear brake switch to fit all 3/4 cylinder carburettor models, Bonneville range, 955 Sprint RS and ST.

 

750/900 Trident, 750/900/1000/1200 Daytona, 900/1200 Trophy, 750/900 Speed Triple, Sprint 900, Sprint Sport, Sprint Executive, Tiger 900/955, Thunderbird 900, Thunderbird Sport, Legend, Adventurer, Sprint 955 ST and RS.



£13.95
More info  

Uprated Nissin front brake master cylinder
( B389 )

Reduce brake lever travel when changing from the original 14mm bore to this 5/8" bore remote pot sports master cylinder.

Dark grey finish on master cylinder.



£135.00
More info  

Uprated Nissin front brake master cylinder (black)
( B399 )

Reduce brake lever travel when changing from the original 14mm bore to this 5/8" bore. Remote pot reservoir sports style master cylinder. 

Black finish on master cylinder

 

 



£145.00
More info  

Nissin hydraulic clutch master cylinder (black)
( B400 )

Nissin clutch master cylinder. Latest sports style with remote reservoir pot. Fits all 3 and 4 cylinder carburettor models. Same 14 mm bore size as original part. Black finish on master cylinder.

Fits 750/900 Trident, 750/900 Speed Triple, 750/900/1000/1200 Daytona, 900/1200 Trophy, Tiger 900 (carburettor), Sprint Sport, Sprint 900, Sprint Executive, Thunderbird 900, Thunderbird Sport, Adventurer and Legend.



£136.00
More info  

Nissin brake pad locator
( B418 )

The 2 piston Nissin caliper used on the rear of many models and  retro front calipers. The caliper moves on slider pins when the brake is applied. The outer brake pad has a hook located in this brake pad locator nut which is screwed onto one of the slider pins. Manufactured from stainless steel. (See slider pins listed below, also in stainless steel).

These fit the front calipers of the following: 750/900 Trident, 900 Sprint and Trophy 900 (up to vin 9083), 1200 Trophy (up to vin 4902),

Fit the rear caliper of the following: 750/900 Trident, 900/1200 Trophy, 750/900 Speed Triple, 750/900/1000/1200 Daytona, Tiger 900 (carburettor model), 955 Daytona, 955 Speed Triple, T595, T509, 1050 Speed Triple, 1050 Tiger, Tiger Explorer, 955 Sprint ST, 1050 Sprint ST, 955 Sprint RS (single sided swinging arm model),

Made in UK



£11.95
More info  

2 piston caliper slider bracket pins (pair)
( B419 )

Stainless steel replacemet pins for the 2 piston (on one side) calipers used  on the rear of most models and front of  very early Trophy, Sprint, and Trident models. The used bracket assembly is shown for reference only to help illustrate pin location.

These fit the front calipers of the following: 750/900 Trident, Tiger 900 (carburettor models), 900 Sprint and Trophy 900 (up to vin 9083), 1200 Trophy (up to vin 4902),

Fits the rear caliper of the following: 750/900 Trident, 900/1200 Trophy, 750/900 Speed Triple, 750/900/1000/1200 Daytona, Tiger 900 (carburettor model), 955 Daytona, 955 Speed Triple, T595, T509, 1050 Speed Triple, 1050 Tiger, Tiger Explorer, 955 Sprint ST, 1050 Sprint ST, Sprint GT, 955 Sprint RS (single sided swinging arm model), Bonneville 800/865, T100, Thruxton, SE, Scrambler, America, Speedmaster

 



£19.95
More info  

Caliper bracket
( B421 )

Threaded rear caliper bracket (less caliper slider pins).

Fits, Trident 750/900, Tiger 900 (carburettor), 900/1200 Trophy, 750/900/1000/1200 Daytona, Sprint 900, Sprint Sport, Sprint Executive



£19.00
More info  

Brake Banjo Bolt Stainless Steel (Single)
( B429 )

Single banjo width Earl's stainless steel brake banjo bolt for most application where x 1 hose is fitted.

M10 x 1.25 pitch thread.



£4.95
More info  

Brake Banjo Bolt Stainless Steel (Double)
( B430 )

Double width banjo stainless steel bolt for x 2 hose connection. Examples are front brake splitter on 3 and 4 cylinder carburettor models.

M10 x 1.25 pitch thread.



£5.49
More info  

Brake Banjo Annealed Copper Washers 10 mm
( B432 )

Original style copper washer 10 mm bore, 15.70 outer diameter and 1.20 mm thick. Pack size 10 pieces. Made in USA.



£3.95
More info  

Disc bolt
( B433 )

Plated steel disc bolt M8 x 1.25 mm pitch. Thread length 30 mm including 10 mm shoulder. The plating isn’t as good as original parts, but the steel is excellent and less prone to chewing up with the hex key.

Fits front and rear on 750/900 Trident, 900/1200 Trophy, 750/900/1000/595/955/1200 Daytona, 750/900/T509/955/ Speed Triple, 900 Sprint, Sprint Sport, Sprint Executive, Sprint RS,

Fits front only on T595, 955 Daytona, T509, 955 Speed Triple, 955/1050 Sprint ST, Sprint RS (single sided swinging arm).



£1.95
More info  

27mm caliper piston and seals (Stainless Steel)
( B436 )

Stainless steel caliper piston 27 mm diameter and 31 mm long with seals for x 1 caliper (x 2 pistons and x 4 seals). These are not genuine Nissin parts.

Fits front and rear calipers on Thunderbird 900, Legend, Thunderbird Sport, Adventurer, 750/900 Trident, 900/955 Tiger, Bonneville, T100, Thruxton, America, Speedmaster, SE, Scrambler, Trophy 900 and Sprint 900 up to vin 9083, Trophy 1200 up to vin 4902

Fits rear caliper only on 750/900/1000/1200 Daytona, 955 Daytona (single sided swinging arm model), 750/900/955/1050 Speed Triple, 900 Sprint Sprint Sport, Sprint Executive, 955/1050 Sprint ST, Sprint RS (single sided swinging arm), Sprint GT, Tiger 1050, Tiger 1050 SE, Trophy 900 and Sprint 900 from vin 9084, Trophy 1200 from vin 4903

Fits front caliper Tiger 800, Tiger XC, Street Triple 675,



£44.95
More info  

Caliper piston 34mm (4 piston caliper)
( B437 )

Larger 34mm diameter trailing piston used in Nissin and ''Triumph'' 4 piston type calipers. Fitted to the front of all Daytona models (up to the use of radial calipers), 900/955 Sprint, Trophy and 900/955 Speed Triples etc.  The pistons are 22.5 mm long. These are genuine Nissin pistons made in Japan.

To fit front calipers on 750/900/1000/1200 Daytona, 750/900 Speed Triple, 900/1200 Trophy, 900 Sprint, Sprint Sport, Sprint Executive, 955/1050 Sprint ST, RS, T509, 955 Speed Triple, T595, 955 Daytona, TT600, Speed 4, 600/650 Daytona, Rocket 3,

 



£19.00
More info  

Caliper piston 30mm (4 piston calipers)
( B438 )

Nissin 4 piston calipers have 2 different size pistons to even out pad wear. This is the smaller 30mm (leading) diameter piston used on 4 piston Nissin calipers. This piston will fit all 4 piston Nissin and ''Triumph'' calipers up to the latest radial style. Piston depth 22.5 mm. This is a genuine Nissin part. Made in Japan.



£15.00
More info  

Brake caliper pins 64 mm
( B606 )

64mm long pad pins used on the rear of many Triumph models. These are also used on the front of all Tridents and early Trophy/Sprint models with twin piston (reaction type) calipers. This style of caliper uses 2 pins  to retain the pads. These are sold as a pair. The pad pins are genuine Nissin parts made in Japan.



£8.99
More info  

Pad Pins. Front 4 Piston Type Caliper.
( B607 )

Pad pins to fit all 4 piston ''Nissin'' and ''Triumph'' calipers. These are approximately 53 mm long.  x1 pin used per caliper to retain the pads, these do not project through the inside of the caliper and finish flush with the caliper body. 955 Daytona, 955 Speed Triple and 600/650 models used a longer pin with a split pin on the inside, the 53 mm long pins are fine as replacements. Sold as a pair. Genuine Nissin parts made in Japan.



£8.99
More info  

Front Brake Caliper Nissin 4 piston type (left) Triumph or Nissin
( B650 )

Nissin original equipment 4 piston front brake caliper. These are fitted to many Triumph models, either with the 'Nissin' or 'Triumph' logo.  Bolt fixing centre distance 90mm. These will fit all Trophy, carburettor Daytona/Speed Triple, all 900 Sprint, 955 Sprint ST/RS and many more, but do not fit the 955 Daytona/Speed Triple which have 83mm fixing centres. This is the left side caliper

750/900/1000/1200 Daytona, 750/900 Speed Triple, 900/1200 Trophy,  900 Sprint Sport,  Sprint Executive, 955 Sprint  ST, 955 Sprint RS,



£169.00
More info  

Front Brake Caliper Nissin 4 piston (right).
( B651 )

Nissin original equipment 4 piston front brake caliper. These are fitted to many Triumph models, either with the 'Nissin' or 'Triumph' logo.  Bolt fixing centre distance 90mm. These will fit all Trophy, carburettor Daytona/Speed Triple, all 900 Sprint, 955 Sprint ST/RS and many more, but do not fit the 955 Daytona/Speed Triple which have 83mm fixing centres. This is the right side caliper

750/900/1000/1200 Daytona, 750/900 Speed Triple, 900/1200 Trophy,  900 Sprint Sport,  Sprint Executive, 955 Sprint  ST, 955 Sprint RS,

 

 



£169.00
More info  

Disc Bolt 10 mm shoulder 30 mm long
( B810 )

Stainless steel disc bolt M8 x 1.25 mm pitch. Thread length 30 mm including 10 mm shoulder.

Fits front and rear on:

Bobber, Bonneville T120, Daytona 750/900/1000/1200, Daytona 600/650, Daytona 675, Daytona 955 (twin sided swinging arm), Rocket III, Speed Four, 750/900 Speed Triple, Sprint 900, Sprint Executive, Sprint Sport, Sprint RS (twin sided swinging arm), Street Cup, Street Scrambler, Street Triple 675, Street Triple R, S RS, Thruxton R (liquid cooled), Tiger 800, Tiger 1050, 750/900 Trident, 900/1200 Trophy, TT600

Fits front only on:

Daytona T595, Daytona 955 (single sided swinging arm), Speed Triple 955/1050, Sprint RS (Single sided swinging arm), Sprint ST 955/1050,



£5.49
More info  

Brake pad Nissin front/rear Trident, Trophy, Sprint
( B906 )

Nissin NS semi metallic front brake pads.

Supplied as 2 pads for x 1 caliper.

Fit rear of the following: 750/900 Trident, 750/900 Speed Triple, 750/900/1000/1200 Daytona, 900/1200 Trophy, Sprint 900, Sprint Sport, Sprint Executive, Tiger 900 (carburettor models), Sprint 955 RS (twin sided swinging arm models),Tiger 955 cast wheels (from vin 198875) and Tiger 1050

Fit the front right side of the following: 750/900 Trident, 900 Trident Sprint and Trophy 900 (up to vin 9082), Trophy 1200 (up to vin 4901)



£33.25
More info  

Brake pad Armstrong sintered Daytona 955, Speed Triple 900, Tiger Explorer
( B918 )

Armstrong sintered front brake pads.

Fits: 955 Daytona, T595, T509, 955 Speed Triple, Tiger Explorer, Rocket III, TT600, Speed 4, Daytona 600/650, 955 Sprint ST, 955 Sprint RS, 1050 Sprint ST, Sprint 1050 GT and can also be fitted to 750/900/1000/1200 Daytona, Trophy 1200 from vin 4902, Trophy 900 and Sprint 900 from vin 9083, Sprint Sport, Sprint Executive, 750/900 Speed Triple,

Supplied as 2 pads for x 1 caliper



£11.95
More info  

Brake pad Nissin Daytona, Speed Triple, Sprint
( B919 )

Nissin NS semi metallic front pads fit all 4 piston Triumph/Nissin 4 piston axial (not radial) calipers. These were used by Triumph on as original equipment on all 3/4 cylinder carburettor models and will also fit later models with the same calipers..

Fits the front of the following: 750/900/1000/1200 Daytona, Trophy 1200 from vin 4902, Trophy 900 and Sprint 900 from vin 9083, Sprint Sport, Sprint Executive, 750/900 Speed Triple, 955 Daytona, T595, T509, 955 Speed Triple, Tiger Explorer, Rocket III, TT600, Speed 4, Daytona 600/650, 955 Sprint ST, 955 Sprint RS, 1050 Sprint ST, Sprint 1050 GT, Supplied as 2 pads for x 1 caliper



£34.00
More info  

Brake pad EBC Organic front Daytona, Trophy, Sprint, 900, 955, 1050
( B921 )

EBC organic semi metallic front brake pads. Now with NRS hook retention system to prevent pad to backing delamination.

Fits the front of the following: 750/900/1000/1200 Daytona, Trophy 1200 from vin 4902, Trophy 900 and Sprint 900 from vin 9083, Sprint Sport, Sprint Executive, 750/900 Speed Triple, 955 Daytona, T595, T509, 955 Speed Triple, Tiger Explorer, Rocket III, TT600, Speed 4, Daytona 600/650, 955 Sprint ST, 955 Sprint RS, 1050 Sprint ST, Sprint 1050 GT,

Supplied as 2 pads for x 1 caliper



£16.95
More info  

Front disc black, 310mm floating. Daytona 900/1200, Speed Triple 900 and Trophy 900/1200
( D012 )

Original style replacement 'floating' 310mm front disc used on 900/1200 Daytona, 750/900 Speed Triple, Sprint 900, Sprint Sport, Sprint Executive and 900/1200 Trophy models with 4 piston Nissin/Triumph calipers. Black centre exactly styled on the first original equipment discs used on Daytona 900/1200 and Speed Triple 900 models. Left or right. Made in UK.

 

 

 

 

 

 



£124.00
More info  

Rear Disc 255 mm Trident, Trophy, Sprint 900, Speed Triple 900, Daytona 900/1200
( D018 )

255 mm rear disc to fit 750/900 Trident, Trophy 900/1200, Daytona 750/900/1000/1200, 750/90 Speed Triple, Trident Sprint, Sprint 900, Sprint Sport and Sprint Executive.

Made in UK.



£79.95
More info  

Front Brake Switch all models
( Z303 )

Original front brake switch made by Alps Electrical Co, Japan to fit all Nissin front brake master cylinders except only the radial brake models. 

Fits: Adventurer, America, Bonneville 800/865, T100, SE, Legend TT, Rocket III, Classic, Roadster, Touring, Scrambler, Speed Four, Speed Triple 750/900, Speed Triple T509, Speed Trilpe 955, Speed Triple 1050 up to VIN 461331,  Speedmaster, Sprint 900, Sprint Sport, Sprint Executive, Sprint St 955, Sprint RS, Sprint ST 1050, Sprint GT, Street Triple, Thruxton, Thunderbird 900, Thunderbird Sport, Thunderbird 1600/1700. Thunderbird Storm, Tiger 800, Tiger 800XC, Tiger 900, Tiger 955, Trident 750/900, Trophy 900/1200, TT600   



£11.95
More info