Show All

Show All

Speed Triple 955 & T509



Contact Us For Details

BRAKE PAD INFORMATION
( B001 )

BRAKE PADS - We stock organic (Armstrong), Semi-sintered (Nissin NS - see picture left) and fully sintered (DP and Nissin ST - see picture left) brake pads. Organic pads are resin bonded, kind to the discs, generally quieter and fine for general road use. Sintered pads are made from metal particles put under pressure and heat, offer the best stopping power, but also cause the most rotor wear and can make the most noise. Virtually all original equipment pads are now sintered. They are also the least affected by adverse conditions and are the pad to choose for high speed and track days. Sintered pads can feel 'grabby' and may lack 'feel' at the lever. Semi-metallic pads fall right in the middle for durability and performance. A trade off between sintered and organic, they still stop well, cause less rotor wear with better lever feel than sintered metallic pads and normally make less noise.

Nissin brake pad compound chart shown left.



Contact Us For Details

Front Brake Master Cylinder Seal kit 14mm
( B005 )

Rebuild kit to fit Nissin 14mm bore front brake master cylinders,

Fits: Daytona 600/650, Daytona T595, 955 Daytona, Rocket III, Classic, Roadster, Speed Four, Speed Triple T509, 955 Speed Triple, 1050 Speed Triple to VIN  461331,   750/900 Trident, Sprint 900 and Trophy 900 up to vin 9082, 955 Sprint ST, 955 Sprint RS, 1050 Sprint ST (up to vin 274425) some fuel injected models have  been retrospectively fitted with 5/8" bore master cylinders to reduce lever travel -check before ordering). Street Triple, Sprint 900 and Trophy 900 up to vin 9082, TT600, Tiger 800, Tiger XC, Tiger 900 (carburettor model)



£24.95
More info  

Rear Brake Master Cylinder Rebuild Kit
( B010 )

Rebuild kit for all Triumph (Nissin) rear brake master cylinders.

Fits America, Bonneville 800/865, T100, 600/650/675/750/900/955/1000/1200 Daytona, 750/900 Trident, 750/900/955/1050 Speed Triple, 900/1200 Trophy, Scrambler, Speed Four, Speemaster, Street Triple, Thunderbird 900, Legend, Adventurer, Thunderbird Sport, Sprint 900, Sprint Sport, Sprint Executive, Sprint ST 955/1050, Sprint GT, 955 Sprint RS, Street Triple, Tiger 800/900/955/1050, Tiger 800, Tiger XC, TT600



£26.95
More info  

4 piston front caliper seal kits for Nissin and Triumph calipers
( B056 )

Fits all Nissin and Triumph front 4 piston calipers on all (Apart from Brembo) Triumph sports and touring models. Kit contains 8 seals (4 outer dust seals and 4 hydraulic seals). To equilize brake pad wear, these calipers use 2 different piston sizes, 30mm (leading) and 34mm (trailing). Use silicone or rubber grease during assembly after cleaning out any corrosion from the dust seal groove. The joint seals on the 2 halves are now also included. The piston seals are genuine Nissin parts as used as original equipment by Triumph. These seals are also used in the 1/2 Nym spec. Triumph calipers. Made in Japan.

Fits: 600/650/675/750/900/955/1000/1050/1200/2300



£22.95
More info  

Seal set 2 piston calipers
( B057 )

27mm caliper seals used on all 2 piston calipers fitted to the Triumph range. These are genuine Nissin seals. The kit contains seals to repair x 1 caliper (4 seals). When fitted correctly in a clean groove, there is a smooth action of the piston with no tying up on the dust seal. After cleaning out any corrosion in the the dust seal groove, always use silicone or rubber grease when fitting.  Made in Japan.

Fits front and rear on:

Bonneville, T100, America, Speedmaster, Scrambler, Street Cup, Street Scrambler, Thruxton,Thunderbird 900, Thunderbird Sport, Legend TT, Adventurer,Trident 750/900, Tiger 900, Tiger 955, Trident Sprint (up to VIN 9082), Trophy 900 (upto VIN 9082), Trophy 1200 (up to VIN 4901)

Fits front only on

Tiger 800, Bobber, T120,

Fits rear on

Daytona 750/900/1000/1200, Daytona T595, Daytona 955, Speed Triple 750/900, Speed Triple T509, Speed Triple 955, 1050, Speed Triple R, S, Sprint ST 955, Sprint ST 1050, Sprint RS (single sided swinging arm), Tiger Explorer, Tiger Sport, Trophy 1215, SE, Trophy 900/1200, Sprint 900, Sprint Executive, Sprint Sport

 

 



£14.95
More info  

Earls brake hose to order
( B076 )

Earls stainless steel braided hose with neatly crimped stainless steel ends can be supplied to order for every model. We charge per hose with the choice of clear, black or no covering on the braiding. Popular models are stocked, others to order in approximately 3 or 4 days. Hoses are supplied with new copper banjo sealing washers. Recently produced models from Triumph are equiped with braided hoses (although the ends are plated not stainless steel) for reduced lever travel over earlier models with their reinforced rubber hoses. Custom lengths no problem. 

Earls stainless steel braided hose with stainless steel banjo crimped ends with new copper sealing washers. 600/650/750/800/865/900/955/1000/1050/1200/2300. Priced per hose. Please state model when ordering.





£29.95
More info  

Front brake reservoir container.
( B193 )

Genuine Nissin front brake reservoir plastic pot used many Triumph models. This inclues the link pipe which fits some but no all models.

Fits  TT600, Speed Four, 600/650/675/955 Daytona, T595, T509, Thruxton, SE, Bonneville (from vin 380777) , 955/1050 Speed Triple, Sprint 955 ST/RS, 1050 Sprint ST, Tiger 1050, Sprint 1050 GT.



£19.99
More info  

Angled inlet to master cylinder with seat/circlip kit
( B194 )

Angled inlet to front brake reservoir used on most sports models. The 'O' ring seal and circlip are the same components used in the inlet to Nissin rear brake master cylinders. Genuine Nissin component. Made in Japan.

Fits TT600, Speed Four, 600/650//955 Daytona, T595, T509, Thruxton, SE, Bonneville (from vin 380777) , 955 Speed Triple, 1050 Speed Triple (up to VIN 461331), Sprint 955 ST/RS, 1050 Sprint ST, Tiger 1050, Sprint 1050 GT



£17.95
More info  

Master cylinder piston outer boot (front)
( B225 )

Nissin front brake master cylinder outer boot. Fits all models with Nissin front brakes.

750/900 Trident, 600/650/750/900/955/1000/1200 Daytona, 750/900/955 Speed Triple, 900/955 Tiger, Thunderbird 900, Thunderbird Sport, Legend, Adventurer, 900/1200 Trophy



£4.95
More info  

Rear brake master cylinder boot Nissin.
( B226 )

Replacement master cylinder boot to fit all Nissin rear brake master cylinders. 



£4.95
More info  

2 piston Nissin caliper pin boots
( B274 )

Slider pin pair of boot/covers for the 2 piston Nissin calipers.

These fit the front calipers of the following: 750/900 Trident, 900 Sprint and Trophy (up to vin 9083), 1200 Trophy (up to vin 4902), Tiger 900, Tiger 900 (EFI), Tiger 955, Tiger 800, Tiger XC, Thunderbird 900, Legend, Thunderbird Sport, Adventurer

Fit the rear caliper of the following: 750/900 Trident, 900/1200 Trophy, 750/900 Speed Triple, 750/900/1000/1200 Daytona, Tiger 900 (carburettor model), 955 Daytona, 955 Speed Triple, T595, T509, 1050 Speed Triple, 1050 Tiger, Tiger 900 (EFI), Tiger 955,  Tiger 800, Tiger XC, Tiger Explorer, 955 Sprint ST, 1050 Sprint ST, Sprint GT, 955 Sprint RS (single sided swinging arm model), Bonneville 800/865, T100, Thruxton, SE, Scrambler, America, Speedmaster, Thunderbird 900, Thunderbird Sport, Legend, Adventurer



£8.95
More info  

Rear brake master cylinder push rod
( B279 )

Rear brake master cylinder rod with a choice of 52 mm, 45 mm or 38 mm of 8 mm x 1.25 pitch thread. This will fit many models and the thread can be cut for most models to shorten to the required length. 

Thunderbird 900, Legend, Adventurer, Thunderbird Sport, T595/955/600/650 Daytona, T509/955/1050 Speed Triple, 955/1050 Sprint ST, 955 Sprint RS, 955/1050 Tiger





£16.00
More info  

Brake bleed screw covers
( B286 )

x 3 rubber bleed screw covers.



£1.95
More info  

Rubber grease sachet
( B291 )

Use a light coating of rubber grease when replacing brake caliper seals. Sachet contents 5g.



£1.75
More info  

Brake paste
( B292 )

Brake paste, ideal for brake pad pin threads.



£1.95
More info  

Rear brake switch hydraulic type.
( B302 )

Replacement rear brake switch to fit all 3/4 cylinder carburettor models, Bonneville range, 955 Sprint RS and ST.

 

750/900 Trident, 750/900/1000/1200 Daytona, 900/1200 Trophy, 750/900 Speed Triple, Sprint 900, Sprint Sport, Sprint Executive, Tiger 900/955, Thunderbird 900, Thunderbird Sport, Legend, Adventurer, Sprint 955 ST and RS.



£13.95
More info  

Uprated Nissin front brake master cylinder
( B389 )

Reduce brake lever travel when changing from the original 14mm bore to this 5/8" bore remote pot sports master cylinder.

Dark grey finish on master cylinder.



£135.00
More info  

Uprated Nissin front brake master cylinder (black)
( B399 )

Reduce brake lever travel when changing from the original 14mm bore to this 5/8" bore. Remote pot reservoir sports style master cylinder. 

Black finish on master cylinder

 

 



£145.00
More info  

Nissin brake pad locator
( B418 )

The 2 piston Nissin caliper used on the rear of many models and  retro front calipers. The caliper moves on slider pins when the brake is applied. The outer brake pad has a hook located in this brake pad locator nut which is screwed onto one of the slider pins. Manufactured from stainless steel. (See slider pins listed below, also in stainless steel).

These fit the front calipers of the following: 750/900 Trident, 900 Sprint and Trophy 900 (up to vin 9083), 1200 Trophy (up to vin 4902),

Fit the rear caliper of the following: 750/900 Trident, 900/1200 Trophy, 750/900 Speed Triple, 750/900/1000/1200 Daytona, Tiger 900 (carburettor model), 955 Daytona, 955 Speed Triple, T595, T509, 1050 Speed Triple, 1050 Tiger, Tiger Explorer, 955 Sprint ST, 1050 Sprint ST, 955 Sprint RS (single sided swinging arm model),

Made in UK



£11.95
More info  

2 piston caliper slider bracket pins (pair)
( B419 )

Stainless steel replacemet pins for the 2 piston (on one side) calipers used  on the rear of most models and front of  very early Trophy, Sprint, and Trident models. The used bracket assembly is shown for reference only to help illustrate pin location.

These fit the front calipers of the following: 750/900 Trident, Tiger 900 (carburettor models), 900 Sprint and Trophy 900 (up to vin 9083), 1200 Trophy (up to vin 4902),

Fits the rear caliper of the following: 750/900 Trident, 900/1200 Trophy, 750/900 Speed Triple, 750/900/1000/1200 Daytona, Tiger 900 (carburettor model), 955 Daytona, 955 Speed Triple, T595, T509, 1050 Speed Triple, 1050 Tiger, Tiger Explorer, 955 Sprint ST, 1050 Sprint ST, Sprint GT, 955 Sprint RS (single sided swinging arm model), Bonneville 800/865, T100, Thruxton, SE, Scrambler, America, Speedmaster

 



£19.95
More info  

Brake Banjo Bolt Stainless Steel (Single)
( B429 )

Single banjo width Earl's stainless steel brake banjo bolt for most application where x 1 hose is fitted.

M10 x 1.25 pitch thread.



£4.95
More info  

Brake Banjo Bolt Stainless Steel (Double)
( B430 )

Double width banjo stainless steel bolt for x 2 hose connection. Examples are front brake splitter on 3 and 4 cylinder carburettor models.

M10 x 1.25 pitch thread.



£5.49
More info  

Brake Banjo Annealed Copper Washers 10 mm
( B432 )

Original style copper washer 10 mm bore, 15.70 outer diameter and 1.20 mm thick. Pack size 10 pieces. Made in USA.



£3.95
More info  

Disc bolt
( B433 )

Plated steel disc bolt M8 x 1.25 mm pitch. Thread length 30 mm including 10 mm shoulder. The plating isn’t as good as original parts, but the steel is excellent and less prone to chewing up with the hex key.

Fits front and rear on 750/900 Trident, 900/1200 Trophy, 750/900/1000/595/955/1200 Daytona, 750/900/T509/955/ Speed Triple, 900 Sprint, Sprint Sport, Sprint Executive, Sprint RS,

Fits front only on T595, 955 Daytona, T509, 955 Speed Triple, 955/1050 Sprint ST, Sprint RS (single sided swinging arm).



£1.95
More info  

27mm caliper piston and seals (Stainless Steel)
( B436 )

Stainless steel caliper piston 27 mm diameter and 31 mm long with seals for x 1 caliper (x 2 pistons and x 4 seals). These are not genuine Nissin parts.

Fits front and rear calipers on Thunderbird 900, Legend, Thunderbird Sport, Adventurer, 750/900 Trident, 900/955 Tiger, Bonneville, T100, Thruxton, America, Speedmaster, SE, Scrambler, Trophy 900 and Sprint 900 up to vin 9083, Trophy 1200 up to vin 4902

Fits rear caliper only on 750/900/1000/1200 Daytona, 955 Daytona (single sided swinging arm model), 750/900/955/1050 Speed Triple, 900 Sprint Sprint Sport, Sprint Executive, 955/1050 Sprint ST, Sprint RS (single sided swinging arm), Sprint GT, Tiger 1050, Tiger 1050 SE, Trophy 900 and Sprint 900 from vin 9084, Trophy 1200 from vin 4903

Fits front caliper Tiger 800, Tiger XC, Street Triple 675,



£44.95
More info  

Caliper piston 34mm (4 piston caliper)
( B437 )

Larger 34mm diameter trailing piston used in Nissin and ''Triumph'' 4 piston type calipers. Fitted to the front of all Daytona models (up to the use of radial calipers), 900/955 Sprint, Trophy and 900/955 Speed Triples etc.  The pistons are 22.5 mm long. These are genuine Nissin pistons made in Japan.

To fit front calipers on 750/900/1000/1200 Daytona, 750/900 Speed Triple, 900/1200 Trophy, 900 Sprint, Sprint Sport, Sprint Executive, 955/1050 Sprint ST, RS, T509, 955 Speed Triple, T595, 955 Daytona, TT600, Speed 4, 600/650 Daytona, Rocket 3,

 



£19.00
More info  

Caliper piston 30mm (4 piston calipers)
( B438 )

Nissin 4 piston calipers have 2 different size pistons to even out pad wear. This is the smaller 30mm (leading) diameter piston used on 4 piston Nissin calipers. This piston will fit all 4 piston Nissin and ''Triumph'' calipers up to the latest radial style. Piston depth 22.5 mm. This is a genuine Nissin part. Made in Japan.



£15.00
More info  

Piston Set 1/2 Nymfron
( B446 )

Set of x 4 Nissin caliper pistons (x 2  30 mm pistons and x 2  34 mm Nymfron low friction pistons). Can be fitted to any Nissin/Triumph 4 piston caliper (not Brembo). Nissin only coat the 34 mm to reduce friction/drag. This was done to help eliminate the long lever travel problems.



£54.00
More info  

Brake Bleed Screw
( B472 )

Brake caliper bleed screw/nipple to fit Nissin calipers used on Triumph models. Genuine Nissin part.



£2.95
More info  

Brake caliper pins 64 mm
( B606 )

64mm long pad pins used on the rear of many Triumph models. These are also used on the front of all Tridents and early Trophy/Sprint models with twin piston (reaction type) calipers. This style of caliper uses 2 pins  to retain the pads. These are sold as a pair. The pad pins are genuine Nissin parts made in Japan.



£8.99
More info  

Pad Pins. Front 4 Piston Type Caliper.
( B607 )

Pad pins to fit all 4 piston ''Nissin'' and ''Triumph'' calipers. These are approximately 53 mm long.  x1 pin used per caliper to retain the pads, these do not project through the inside of the caliper and finish flush with the caliper body. 955 Daytona, 955 Speed Triple and 600/650 models used a longer pin with a split pin on the inside, the 53 mm long pins are fine as replacements. Sold as a pair. Genuine Nissin parts made in Japan.



£8.99
More info  

Disc Bolt 10 mm shoulder 30 mm long
( B810 )

Stainless steel disc bolt M8 x 1.25 mm pitch. Thread length 30 mm including 10 mm shoulder.

Fits front and rear on:

Bobber, Bonneville T120, Daytona 750/900/1000/1200, Daytona 600/650, Daytona 675, Daytona 955 (twin sided swinging arm), Rocket III, Speed Four, 750/900 Speed Triple, Sprint 900, Sprint Executive, Sprint Sport, Sprint RS (twin sided swinging arm), Street Cup, Street Scrambler, Street Triple 675, Street Triple R, S RS, Thruxton R (liquid cooled), Tiger 800, Tiger 1050, 750/900 Trident, 900/1200 Trophy, TT600

Fits front only on:

Daytona T595, Daytona 955 (single sided swinging arm), Speed Triple 955/1050, Sprint RS (Single sided swinging arm), Sprint ST 955/1050,



£5.49
More info  

EBC Organic Brake Pads Bonneville (rear), 900, 955, 1050
( B909 )

EBC organic brake pads. Supplied as 2 pads for x 1 caliper.

Fits the rear of the following: Tiger Explorer, Bonneville, T100, Scrambler, America, Speedmaster. All single sided models T595 Daytona, 955 Daytona, T509, 955 Speed Triple, 1050 Speed Triple, 955 Sprint ST, 1050 Sprint ST, Sprint 955 RS (single sided swinging arm models), Trophy 1215 & SE, Tiger Sport

Fits the front left side of the following: 750/900 Trident, 900 Trident Sprint and Trophy 900 up to vin 9082, Trophy 1200 up to vin 4901



£16.95
More info  

Brake pad Nissin Bonneville (rear), 955, 1050
( B910 )

Nissin NS semi metallic brake pads. Supplied as 2 pads for x 1 caliper.

Fits the rear of the following: Tiger Explorer, Bonneville, T100, Scrambler, America, Speedmaster. All single sided models T595 Daytona, 955 Daytona, T509, 955 Speed Triple, 1050 Speed Triple, 955 Sprint ST, 1050 Sprint ST, Sprint 955 RS (single sided swinging arm models), Trophy 1215 & SE, Tiger Sport

Fits the front left side of the following: 750/900 Trident, 900 Trident Sprint and Trophy 900 up to vin 9082, Trophy 1200 up to vin 4901



£33.25
More info  

Brake pad Armstrong Bonneville (rear), 955, 1050, 900 left front
( B911 )

Armstrong brake pads. Supplied as 2 pads for x 1 caliper.

Fits the rear of the following: Tiger Explorer, Bonneville, T100, Scrambler, America, Speedmaster. All single sided models T595 Daytona, 955 Daytona, T509, 955 Speed Triple, 1050 Speed Triple, 955 Sprint ST, 1050 Sprint ST, Sprint 955 RS (single sided swinging arm models), Trophy 1215 & SE, Tiger Sport

Fits the front left side of the following: 750/900 Trident, 900 Trident Sprint and Trophy 900 up to vin 9082, Trophy 1200 up to vin 4901



£12.95
More info  

Brake pad Armstrong sintered Daytona 955, Speed Triple 900, Tiger Explorer
( B918 )

Armstrong sintered front brake pads.

Fits: 955 Daytona, T595, T509, 955 Speed Triple, Tiger Explorer, Rocket III, TT600, Speed 4, Daytona 600/650, 955 Sprint ST, 955 Sprint RS, 1050 Sprint ST, Sprint 1050 GT and can also be fitted to 750/900/1000/1200 Daytona, Trophy 1200 from vin 4902, Trophy 900 and Sprint 900 from vin 9083, Sprint Sport, Sprint Executive, 750/900 Speed Triple,

Supplied as 2 pads for x 1 caliper



£11.95
More info  

Brake pad Nissin Daytona, Speed Triple, Sprint
( B919 )

Nissin NS semi metallic front pads fit all 4 piston Triumph/Nissin 4 piston axial (not radial) calipers. These were used by Triumph on as original equipment on all 3/4 cylinder carburettor models and will also fit later models with the same calipers..

Fits the front of the following: 750/900/1000/1200 Daytona, Trophy 1200 from vin 4902, Trophy 900 and Sprint 900 from vin 9083, Sprint Sport, Sprint Executive, 750/900 Speed Triple, 955 Daytona, T595, T509, 955 Speed Triple, Tiger Explorer, Rocket III, TT600, Speed 4, Daytona 600/650, 955 Sprint ST, 955 Sprint RS, 1050 Sprint ST, Sprint 1050 GT, Supplied as 2 pads for x 1 caliper



£34.00
More info  

Brake pad EBC Organic front Daytona, Trophy, Sprint, 900, 955, 1050
( B921 )

EBC organic semi metallic front brake pads. Now with NRS hook retention system to prevent pad to backing delamination.

Fits the front of the following: 750/900/1000/1200 Daytona, Trophy 1200 from vin 4902, Trophy 900 and Sprint 900 from vin 9083, Sprint Sport, Sprint Executive, 750/900 Speed Triple, 955 Daytona, T595, T509, 955 Speed Triple, Tiger Explorer, Rocket III, TT600, Speed 4, Daytona 600/650, 955 Sprint ST, 955 Sprint RS, 1050 Sprint ST, Sprint 1050 GT,

Supplied as 2 pads for x 1 caliper



£16.95
More info  

YB14LA2 gel sealed battery
( BA019 )

Sealed maintenance free LP/JMT gel battery. Upgrade/replaces YB14LA2

Fits: 750/900 Trident, 900/1200 Trophy, Legend, Thunderbird, Thunderbird Sport ,Adventurer, 750/900/1000/1200 Daytona, 750/900 Speed Triple, Sprint 900, Sprint Sport, Sprint Executive and Tiger 900

Also fits: T595/955 Daytona up to vin 71698, T509/955 Speed Triple up to vin 79696 



£53.95
More info  

Front Wheel Bearings 600/675/955
( BE070 )

x 2 Koyo front wheel bearings to fit

TT600, Speed Four, Daytona 600/650, Daytona 675, Street Triple, 955 Speed Triple from VIN 141872, 955 Daytona from VIN 132513,



£17.00
More info  

Front Wheel Bearings Trident, daytona, Trophy, 955 ST and RS
( BE072 )

x 2 Koyo bearings to fit

Front wheel on 750/900 Trident, 750/900/1000/1200 Daytona, Daytona T595, 955 Daytona (up to VIN 132512), 900/1200 Trophy, Sprint 900, Sprint Sport, Sprint Executive, Thunderbird 900, Legend, Adventurer, Thunderbird Sport, 750/900 Speed Triple, Speed Triple T509, 955 Speed Triple (up to VIN 141871), America (spoked wheel), America (cast wheel) 1050 Sprint ST, 1050 Sprint GT, 1050 Speed Triple (From VIN 210445 to VIN 461331, Tiger 1050 (From VIN 287504 to VIN 570058),

Rear wheel  on America (cast wheel)

 

 



£17.00
More info  

Sprocket Carrier Bearing Single sided Swinging Arm Models
( BE600 )

Japanese twin ball 55X35X20 NTN bearing and dust seal to fit sprocket carrier (cush drive) on single sided swinging arm models. NTN has been used as the original equipment bearing.

Fits Daytona T595, Speed Triple T509, Daytona 955 (single sided), Sprint ST 955/1050, Sprint GT, Sprint RS 955 (single sided), Speed Triple 955/1050 and 1050 Tiger and Tiger Sport.



£31.95
More info  

Rear Wheel Bearings/Seals Single Sided Swinging Arm Models
( BE601 )

Rear wheel bearings (rear axle eccentric adjuster bearings), double ball bearing and needle roller with x 2 separate seals.

Fits T595, T509, 955 Speed Triple, 955 Daytona, 955 Sprint ST,single sided swinging arm Sprint RS, 1050 Sprint ST up to VIN 388246 and 1050 Speed Triple up to vin 346969.



£69.00
More info  

Valve Shims 25 mm 2.05 - 2.25
( BE699 )

Valve shim 25 mm diameter. Sizes from 2.05 to 2.25.

Fits: Adventurer, America, Bonneville, T100 & SE, Daytona 750, 900, 1000, 1200, Daytona T595, Daytona 955 up to VIN 132512, Legend, Rocket III, Classic, Roadster & Touring, Scrambler, Speedmaster, 750 & 900 Speed Triple, Speed Triple T509, 955 Speed Triple up to VIN 141871, Sprint 900, Sprint Sport, Sprint Executive, Sprint RS & ST 955 up to VIN 139276, Thruxton, Thunderbird 900, Thunderbird Sport, Tiger 900 (carburettor), Tiger 900 (injection), Tiger 955i, 750 & 900 Trident, Trophy 900 & 1200





£7.95
More info  

Valve Shims 25 mm 2.30 - 3.20
( BE700 )

Valve shim 25 mm diameter. Sizes from 2.30 to 3.20

Fits: Adventurer, America, Bonneville, T100 & SE, Daytona 750, 900, 1000, 1200, Daytona T595, Daytona 955 up to VIN 132512, Legend, Rocket III, Classic, Roadster & Touring, Scrambler, Speedmaster, 750 & 900 Speed Triple, Speed Triple T509, 955 Speed Triple up to VIN 141871, Sprint 900, Sprint Sport, Sprint Executive, Sprint RS & ST 955 up to VIN 139276, Thruxton, Thunderbird 900, Thunderbird Sport, Tiger 900 (carburettor), Tiger 900 (injection), Tiger 955i, 750 & 900 Trident, Trophy 900 & 1200

 





£3.95
More info  

Valve Shims 9.5 mm 1.70 - 2.95
( BE702 )

9.5 mm valve shim.

Fits: Daytona 955 from VIN 132513, 955 Speed Triple from VIN 141872, 1050 Speed Triple, 1050 Speed Triple R, 955 ST and RS from VIN 139277,  1050 Sprint ST, 1050 Sprint GT, Tiger 1050, Tiger Explorer and XC, Trophy 1215





£3.95
More info  

Lever Clamp/Mirror Support
( C195 )

Replacement clamp/mirror support or new clamp for models with no mirror fixing. Used as original on clutch and front brake lever on 955/1050 Speed Triple, Speed Four, Thruxton, SE, Bonneville (from vin 380777), 955/1050 Tiger. Ideal to hold mirrors when converting Daytona 955/T595 to Speed Triple. 10mm threaded lever clamp used on many unfaired models for mirror fixing.  Made in Japan. 

Fits: Bonneville (from VIN 380777), SE, Scrambler, Speed Four, Speed Triple 955, T509, 1050 Speed Triple, Street Cup, Street Scrambler, Street Triple, Street Triple R, Street Twin, Thruxton 900, Tiger 1050



£9.95
More info  

Lever Clamp/Mirror Support
( C195 )

Replacement clamp/mirror support or new clamp for models with no mirror fixing. Used as original on clutch and front brake lever on 955/1050 Speed Triple, Speed Four, Thruxton, SE, Bonneville (from vin 380777), 955/1050 Tiger. Ideal to hold mirrors when converting Daytona 955/T595 to Speed Triple. 10mm threaded lever clamp used on many unfaired models for mirror fixing.  Made in Japan. 

Fits: Bonneville (from VIN 380777), SE, Scrambler, Speed Four, Speed Triple 955, T509, 1050 Speed Triple, Street Cup, Street Scrambler, Street Triple, Street Triple R, Street Twin, Thruxton 900, Tiger 1050



£9.95
More info  

Clutch lever 600/650/675/955 Daytona, Street Triple and 955 Speed Triple.
( C347 )

Replacement lever for Daytona 600/650, 675 Daytona and Street Triple 675. Also fits Speed Four after vin 201642, 955 Daytona models from vin 186150. Late model single sided swinging arm 955 Sprint RS from vin 186151.



£11.50
More info  

Clutch lever 600/650/675/955 Daytona, Street Triple and 955 Speed Triple.
( C347 )

Replacement lever for Daytona 600/650, 675 Daytona and Street Triple 675. Also fits Speed Four after vin 201642, 955 Daytona models from vin 186150. Late model single sided swinging arm 955 Sprint RS from vin 186151.



£11.50
More info  

Clutch lever T595/955 Daytona, 955 ST/RS and 955 Speed Triple.
( C348 )

Clutch lever fits all TT600, Speed Four as well as 955 Sprint RS/ST, T595/955 Daytona and 955 Speed Triple models up to VIN 186150.



£10.00
More info  

Clutch lever T595/955 Daytona, 955 ST/RS and 955 Speed Triple.
( C348 )

Clutch lever fits all TT600, Speed Four as well as 955 Sprint RS/ST, T595/955 Daytona and 955 Speed Triple models up to VIN 186150.



£10.00
More info  

Adjustable Front brake lever 600/650/955 Daytona and 955 Speed Triple.
( C354 )

Correct shape replacement front brake lever to fit TT600, Speed Four, 600/650 Daytona, Street Triple 675, Scrambler, Thruxton, SE and Bonneville from vin 380777, T509 Speed Triple, T595/955 Daytona, 955 Speed Triple, 1050 Speed Triple up to vin 333179 and 1050 Tiger.

Will also fit to upgrade to adjustable on Bonneville, T100, America and Speedmaster.



£16.95
More info  

Speedo cable 86cm
( CC718 )

Speedo cable 86cm long.

Take care not to over tighten the 5 mm screw holding the cable into the drive unit



£14.95
More info  

Clutch Cable T509 and 955 Speed Triple.
( CC726 )

Clutch cable to fit T509, 955 Speed Triple 1997-2001 (up to VIN 141871) and T595/955 Daytona models converted to Speed Triple style.



£15.00
More info  

Throttle Cable Daytona T595, Speed Triple 955, Daytona 955
( CC732 )

Throttle cable Inner length approximately130 cm long. Also available + 11 cm for higher bar converstions.

Daytona T595

Daytona 955 up to VIN 132512

Speed Triple T509

Speed Triple 955 up to VIN 141871





£19.95
More info  

Clutch Cable Speed Triple 955 01>
( CC774 )

Replacement clutch cable to fit 955 Speed Triple from VIN 141872. Outer length 99 cm. Inner cable length 107 cm.



£15.00
More info  

Expansion Tank Elbow
( CL344 )

Black plastic elbow to fit expansion tanks. Sealing problems on the radiator to expansions tanks can allow water expansion but no siphon back with loss of coolant in the radiator.



£1.39
More info  

Water Pump Joint Seal
( CL499 )

Replacement red joint seal for when water pump is disturbed. O-ring where pump enters the engine and copper sealing washer under joint screw are also included (on some models).

Fits T595, T509, 955 Daytona, T509 Speed Triple, 955 Speed Triple, 1050 Speed Triple, 955 Sprint ST, 955 Sprint RS, 1050 Sprint ST, Sprint GT, Tiger 900 (EFI), Tiger 955, 1050 Tiger, Tiger Sport



£3.95
More info  

Clutch plate set. 955 models (early engine)
( CL932 )

Clutch friction plate set (9 peices) to fit Daytona T595, T509, 955 Daytona up to VIN 132512, Speed Triple up to VIN141871, 900 Tiger (EFI), 955 Sprint ST and 955 Sprint RS up to VIN 139277.



£59.00
More info  

Clutch plate set. 955 models (later engine) and 1050
( CL933 )

Clutch friction plate set (10 peices) to fit Daytona 955 Daytona from VIN 132513, 955 Speed Triple from VIN141872, and 955 Sprint ST and 955 Sprint RS from VIN 139278. Also fits 1050 Speed Triple up to VIN 461331.



£69.00
More info  

Clutch Spring Set 955 and 1050
( CL935 )

EBC 15% uprated clutch spring set to fit all 955 and 1050 models.



£12.95
More info  

Cush Drive Rubbers Single Sided Swinging Arm Models
( CS114 )

Set of x 5 cush rubbers. Replaces Triumph T1224400

Fits: Daytona T595, 955 Daytona, 955 Speed Triple, 1050 Speed Triple, 955 Sprint RS (single sided swinging arm), 955 Sprint ST, 1050 Sprint ST, Sprint GT, 1050 Tiger Sport



£27.95
More info  

Gearbox sprockets 900/1200/955/1050 (530)
( CS141 )

Gearbox sprockets available in 17, 18 or 19 teeth for all carburettor 3/4 cylinder models, all 955 and all 1050 models. Smaller than standand gives improved acceleration at the expense of fuel consumption and on some models increased chain guide wear. Larger than standard engine sprockets lose out slightly on acceleration but have a more relaxed feel in top gear.  Please state size when ordering. (530 chain size).





£15.00
More info  

DID Chain and Sprocket Kit (530)
( CS145 )

530 VX gold heavy duty X-ring DID chain with sprockets, tab washer and sprocket cover gasket if required. Please state model when ordering and if in doubt just let us know what sprocket sizes you would like. (530 chain size). Front/rear/chain length details given are for standard factory sizes. Other size choice no problem.  





£125.00
More info  

DID X-ring gold chain 530
( CS155 )

Original equipment DID VX  X-ring gold chain 530 size (5/8 x 3/8). Fits all 750, 900 (3/4 cylinder),1000, 955, 1200 and 1050 models.





£89.00
More info  

Tab Washer Gearbox Sprocket 2, 3 and 4 cylinder carburettor models, 955, 1050.
( CS176 )

Gearbox sprocket tab (locking) washer to fit all of the Bonneville range (carburettor and EFI), 955, 1050 and 3/4 cylinder carburettor models. Replaces Triumph T1180181

 

Fits 750/900 Trident, 900/1200 Trophy, 750/900/1000/1200 Daytona, Super III, 900 Tiger, 750/900 Speed Triple, 900 Sprint, Sprint Sport, Sprint Executive, Thunderbird 900, Thunderbird Sport, Legend, Adventurer, T595, 955 Daytona, T509, 955 Speed Triple, 955 Sprint ST, 955 Sprint RS, 955 Tiger, 1050 Tiger, Tiger Sport, 1050 Sprint ST, 1050 Sprint GT, 1050 Speed Triple, Bonneville 800/865, T100, Scrambler, America, Speedmaster, Thruxton and SE.

Tab Washer Gearbox Sprocket 3 and 4 cylinder carburettor models, 955, 1050.



£3.95
More info  

Rear Sprocket Single Sided Swinging Arm Models (530)
( CS663 )

Rear sprockets available in 42, 43, 44 or 45 teeth to fit all single sided swinging arm models. Please state size when ordering.  (530 chain size).

T595. T509, 955 Daytona, 955/1050 Speed Triple, 955/1050 Sprint ST, 955 Sprint RS (single sided swinging arm)





£25.00
More info  

Chain Rivet Tool
( CS950 )

Replica DID chain rivet tool. This will push the rivet link together and neatly rivet the ends over. To separate an old chain or shorten a chain, grind the rivet ends one side of the link to be removed until the side plate is hit. Go slightly below the surface to be sure the rivetting is well ground away, then knock apart with a punch and hammer.



£39.95
More info  

320mm front disc 5 hole fitting for Daytona 955 (pair)
( D014 )

x 2 front discs 320 mm with 6mm offset.

To fit: Daytona 955 from vin 132513,  Speed Triple 955 from vin 141872

Please check the off set before ordering (inside face against the wheel to the inside face of the disc rotor).

Made in UK.



£235.00
More info  

Rear Disc 220 mm T595, T509, 955 Daytona, 955 Speed Triple
( D016 )

220 mm rear disc to fit TT600, Speed Four, Daytona 600, Daytona 650, T595, T509, 955 Daytona, 955 Speed Triple, 1050 speed Triple, 675 Daytona and Street Triple.



£69.00
More info  

Regulator 955
( EG399 )

Regulator fits inside alternator on all 955 models with alternator behind engine. Daytona T595, Daytona 955 up to vin 132512, 955 Sprint ST and RS up to vin 139275. Also fits Trophy 1200 made after vin 55346 and injected Tiger 900.



£39.95
More info  

Regulator Rectifier Electrex unit 600/650/955 /1050
( EG684 )

Hi-power series regulator rectifier with MOSFET technolgy. UK based company Electrex have taken a fresh look at this problem part. This is the very latest Electrex unit with direct connection to the battery terminals bypassing problems associated by going through the wiring loom. Supply from the alternator is now via a new heavy duty connector. Supplied with instructions. New connectors have to be crimped onto the wiring coming from the alternator which are supplied. This takes a few minutes but is well worth the effort.

  • Super effiecient 'MOSFET' regulator rectifier.
  • Direct fused connection to the battery to avoid common connection faults in the wiring loom.
  • Works where airlow is limited.
  • In-built thermal protection.
  • Manufactured in the UK.

 

This Electrectex unit fits Daytona 955 from vin 132512, 955 Speed Triple from vin 141872, 955 Sprint ST and Sprint RS from vin 139277, Speed Four, Daytona 600, Daytona 650, 1050 Speed Triple, 1050 Tiger and all Tiger 955.

 



£114.00
More info  

Headlamp rim to fit Speed Four,955/1050 Speed Triple, Rocket 3. .
( EL026 )

Chrome headlamp rim to fit all urban round twin headlight models. Speed Four, 675 Street Triple, T509/955/1050 Speed Triple and Rocket 3. Replaces Triumph T2700560 

Can also be used to replace the black headlight rim used on:Thunderbird Storm and Bonneville Bobber.

EL027 is a black version of this chrome rim.



£19.95
More info  

Xenon headlight bulb H4
( EL107 )

Xenon 60/55 w 472 H4 type headlight bulb, 30% brighter than standard. Fits all carburettor models and all 955 models.



£7.50
More info  

Speed Triple twin headlight pivot
( EL152 )

Replica T509/955 Speed Triple headlight pivot on models up to 2002 , used on twin headlamp assembly. 70mm hole centres.



£26.00
More info  

Headlight, twin replacement Speed Triple (Pair)
( EL391 )

Direct replacement flat glass symetrical dip/low beam light units with headlight bulbs and side light hole. Supplied as pairs, as the units although similar are not exactly the same as the originals.

Fits T509, Speed Triple 955, Speed Triple 1050, Speed Four, Street Triple



£69.00
More info  

Indicator left. Daytona T595, 955, T509 Speed Triple
( EL403 )

Left side front indicator complete (also right side rear) with correct wiring which connects into original Triumph wiring loom.

T509, Daytona T595, 955 Daytona, 955 Speed Triple.



£14.95
More info  

Indicator right. Daytona T595, 955, T509 Speed Triple
( EL404 )

Right side front indicator complete (also left side rear) with correct wiring which connects into original Triumph loom.

T509, Daytona T595, 955 Daytona, 955 Speed Triple.



£14.95
More info  

Exhaust studs steel, all 3 cylinder models
( EX083 )

Set of 6 steel exhaust studs.  (M8 x 1.25 pitch thread both ends)  Approximately 38mm overall length. All  3 cylinder models.



£9.95
More info  

Exhaust header stainless steel studs (priced each)
( EX085 )

Stainless stud with copper plated flanged nut.

750/900 Trident, 900/1200 Trophy, 750/900/955/1050 Speed Triple, 750/900/955/1000/1200 Daytona, 900/955/1050 Tiger, 900 Thunderbird, Legend, Thunderbird Sport, Adventurer, 955/1050 Sprint ST, 955 Sprint RS



£3.95
More info  

Gear change lever rubber
( F089 )

These are very high quality gear change rubbers, which will outlast the original part. 41 mm long.

To Fit:

Sprint 900, Sprint Sport, Sprint Executive and Trident Sprint.

Speed Triple 750/900

Trophy 900/1200

Trident 750/900

Daytona 750, 900, 1000, 1200

Tiger 900 carburettor and injection (EFI)

Tiger 955

TT600 and Speed Four

Sprint 955 RS and 955 ST (up to VIN 139276)

Daytona T595 and 955 from VIN 87317 (one piece 'reverse' gear lever)

Speed Triple 955 from VIN 87317 (one piece 'reverse' gear lever)



£1.75
More info  

Riders Foot Rest with rubbers for extra grip available for T.595/955 Daytona
( F162 )

Footrest with rubber and hero blob fit T595, T509, all 955 Daytona and 955 Speed Triple all models. Sold as a pair.



£34.95
More info  

Crash bungs T595/955I Daytona, T509/955 Speed Triple
( F426 )

Quality UK manufactured crashbungs with stainless steel shaft. Offset design to eliminate having to cut the fairing panels. Fit Daytona T595, 955 Daytona 1999 > 06, T509, 955 Speed Triple. Sold as a pair.



£89.00
More info  

Lever Bush T595/T509/955 (16mm)
( F621 )

Brake pedal and gear change pivot bushes to fit Speed Triple T509, Daytona T595, 955 Speed Triple up to vin 141872 and Daytona 955 up to vin 132513.



£4.25
More info  

Front guard extender 1050 Tiger, 955/1050 Speed Triple, 955 Daytona
( G317 )

Front guard extender to fit 955 Speed Triple (VIN 141872>),  955 Daytona (VIN 132513>), 1050 Tiger and 1050 Speed Triple.



£19.99
More info  

Bar end weights to fit Daytona T595/955, 955 Speed Triple and Thruxton, black steel (priced per pair)
( H090 )

Gloss black coated steel bar end weighs (150 gram each) to replace original black aluminium alloy bar end weights. These are much heavier to change the natural vibration/frequency.  Sold as a pair. Will fit handlebars with tubular (not solid) section at the end to a depth of 52 mm with18 mm inside diameter required. Bar end weight is 25 mm outside diameter. 

Fits T509, T595, 955 Daytona up to vin 132513, 955 Speed Triple and Thruxton.



£12.95
More info  

Bar end weights to fit...
( H116 )

Black coated aluminium bar replacement weights. Sold as a pair.

Fit T509, T505, 955 Daytona (up to vin 132513), Thruxton.



£7.95
More info  

T509/955/1050 Speed Triple handlebars Replaces Triumph T2040731
( H156 )

Chrome 7/8 " (22 mm) handlebars manufactured in the UK to the original size & shape with drilled holes for locating switch gear and knurled grip areas for the bar clamps. 

Fits:  Speed Triple T509, 955 & 1050 Speed Triple up to VIN 333178.

735 mm (29 ") wide, 70 mm (2 3/4 ") rise and 115 mm (4 1/2") pull back.

Replaces Triumph T2040731

 

 

 



£39.95
More info  

Handlebar pivot pin T595 and early 955 Daytona.
( H159 )

Stainless steel pivot pin 6.5 mm diameter used on the first series handlebars on T595 and 955i Daytona models. Please check pin size as these were supplied in 5 mm or 6.5 mm. We no longer have the 5 mm pins.



£9.95
More info  

Handlebar R/h T595/955 Daytona
( H160 )

Replacement bar  for all T595 and 955 Daytona up to approximately 1999 with multipiece clip-on design.



£19.00
More info  

Haynes repair manual, 900 fuel injected and 955 Models
( H220 )

All fuel injected 900 and 955 models.



£19.99
More info  

Adjustable clip on handlebar with 70mm riser for 45mm fork size
( H270 )

Fully adjustable clip on handlebar set with 70 mm rise, ideal for adapting to 2000 on 955 Daytona models which have the one piece construction clip on handlebars. Original handlebars have 35 mm rise as standard. These fully adjustable clip on handlebars give an extra 35 mm rise to reduce weight on wrists.

 

 





£159.95
More info  

Fuel Filler cap 600, 650, 675, 800, 955, 1050
( J017 )

Replacement filler cap and 2 keys.

Fits 600/650/675/955 Daytona, 955/1050 Speed Triple, Speed Four, Sprint ST 955, Sprint RS 955, Sprint ST 1050, 955/1050 Tiger, 675 Street Triple, Tiger 800, Tiger XC, T595, T509



£49.95
More info  

Fuel Connector O-Rings
( J183 )

Fuel connector  O-rings x 2 used on fuel injected models. These  O-rings are manufactured from Viton.

While ethanol mixed with petrol/gasoline is known to lower engine / tailpipe emissions, these blended fuels  increased permeation through plastic and rubber. Viton has excellent chemical resistance and helps resist these problems. When removing a fuel connector, make sure the clip is released and while separating keeping square at all times until fully apart.

Fits T595, T509, 955 Daytona, 955 Speed Triple, TT600, Speed Four, Sprint 995 ST, Sprint 995 RS, Tiger 900 (injected) and Tiger 955.



£1.90
More info  

Fuel Filter Injected Models EFI
( J184 )

Mahle KL145 fuel filter to fit:

Bonneville America EFI, Speedmaster EFI, Bonneville EFI, Scrambler EFI, Thruxton EFI, Rocket 3, Rocket 3 Classic, Rocket 3 Touring, Tiger 900 (injection), Tiger 955i, Sprint ST 955, Sprint RS 955, Speed Triple 955, TT600, Daytona 600, Daytona 650 and Speed Four 600



£12.95
More info  

Oil Filter OE Fits all Injected Models
( J185 )

Genuine Triumph oil filter fits all Bonneville (carburettor and EFI) and all Triumph models produced with fuel injection.

Fits: America, Bonneville 800/865, SE, T100, Bobber, T120, Daytona 600/650/675/955, T595, Rocket III, Classis, Roadster, Touring, Scrambler, Speed Four, Speedmaster, Speed Triple 955/1050, T509, Sprint ST 955/1050, Sprint RS, Street Cup, Street Scrambler, Street Triple 675/765, Street Twin, Thruxton 900/1200 R, Thunderbird 1600/1700, Sport, Storm, Tiger 800/900 EFI, 955, 1050, Sport, 1215 Explorer, Trophy 1215, TT600



£9.95
More info  

Oil filter wrench 955/1050/Bonneville range
( J187 )

Professional quality 3/8" drive or 19mm spanner size wrench for fitting and removal of genuine Triumph cannister oil filters on all Bonneville, Rocket 3, 600, 650, 675, 800, 955 and 1050  models.

 



£12.95
More info  

Sump plug washer 14 mm
( J189 )

x 4 sump plug washers to fit all models (expect a few models made in 1991-92 up to VIN 3926). Also fits Tiger Explorer final drive unit, 955 and 3/4 cylinder carburettor model oil cooler to hose joints.



£1.45
More info  

Sump Plug Bolt Magnetic
( J191 )

Sump plug bolt with magnetic insert to fit all models produced since 1994 (after approx. VIN  5000). M14 thread.  19 mm spanner size.



Contact Us For Details

Air Filter Pipercross T595, T509, 955 Sprint ST and RS
( J958 )

Pipercross performance filter to fit Daytona T595, Speed Triple T509, 955 Daytona up to VIN 132512, 955 Speed Triple up to VIN 141871, 955 Sprint RS/ST up to vin 139277, Tiger 900 EFI and Tiger 955.



£34.95
More info  

Air filter Pipercross for 955 Daytona, Speed Triple and Sprint ST/RS
( J960 )

Pipercross performance air filter to fit 955 Daytona (from vin 132513), 955 Sprint ST (from vin 139277) and 955 Sprint RS (from vin 139277)



£36.95
More info  

Left Side Crank Cover Gasket all 955 up to 2001
( K810 )

Left side crank cover gasket fits the first generation 955 engine (generator behind the engine block type) and also the 900 fuel injected Tiger. This cover holds the breather seal which often needs changing when the engine has sudden high oil consumption.



£3.95
More info  

Rotary Breather Seal and Gasket 955 Sprint ST and RS (early style engine)
( K856 )

Rotary Breather Seal and Gasket to fit 955 Sprint ST and Sprint RS up to VIN 139276, Daytona 955 up to VIN 132512, 955 Speed Triple up to VIN 141871, Tiger 900i (EFI), Daytona T595 and T509.



£17.95
More info  

Generator Cover Gasket all 1050 and later 955 engines. Replaces Triumph T1261098
( K857 )

Left side front engine cover gasket. Fits all 1050 engines, 955 Tiger, Daytona 955 from VIN 132513, 955 Speed Triple from VIN141872, 955 Sprint ST from VIN 139277 and 955 Sprint RS from VIN 139277

Replaces Triumph T1261098



£4.95
More info  

Rotary Breather Seal and Gasket to fit 955 (later style engines)
( K858 )

Rotary breather seal and paper gasket to fit later style 955 engines generator engine cover - left side front engine cover. Oil in the airbox, smoke from the exhaust and excessive oil consumption are signs that this seal needs changing. Fits 955 Tiger, Daytona 955 from VIN 132513, 955 Speed Triple from VIN141872, 955 Sprint ST from VIN 139277 and 955 Sprint RS from VIN 139277



£18.95
More info  

Gasket Set 955 early style engine
( K891 )

Lower engine cover gasket set to fit Tiger 900 (EFI), Daytona T595, 955 Daytona up to VIN 132512, T509, 955 Speed Triple up to VIN 141871, 955 Sprint ST and RS up to VIN 139276



£14.95
More info  

Gasket and seal set 955 early style engine
( K892 )

Lower engine cover gasket and seal set to fit Daytona T595, 955 Daytona up to VIN 132512, 955 Speed Triple up to VIN 141871, 955 Sprint ST and RS up to VIN 139276



£49.95
More info  

Gasket and seal set to fit Tiger 900 (EFI) and T509 Speed Triple
( K893 )

Lower engine cover gasket and seal set to fit Tiger 900 (EFI) and T509 Speed Triple



£49.95
More info  

Gasket Set 955 and 1050
( K901 )

Lower engine cover paper gasket set to fit later style 955 and all 1050 engines. Fits 955 Tiger, Daytona 955 from VIN 132513, 955 Speed Triple from VIN141872, 955 Sprint ST from VIN 139277, 955 Sprint RS from VIN 139277, 1050 Sprint ST, 1050 Sprint GT, 1050 Speed Triple, Speed Triple R, Speed Triple S, 

The right side small starter clutch cover changed from from VIN 491324 all 1050 models. This gasket is also included in every set.

 

 



£18.95
More info  

Cam Cover Seal Set 955 and 1050 models.
( K920 )

Cam cover seal set to fit all 1050 and later 955 engines. Large outer seal, cam cover screw seals x 6 and spark plug tunnel seals x 3.

Fits: 955 ST and 955RS from VIN 139277,  Daytona 955 from VIN132513, Speed Triple 955 from VIN141872, 1050 Speed Triple, 1050 Speed Triple S, 1050 Speed Triple R, Speed Triple S, 1050 Tiger, Tiger Sport, 1050 Sprint ST and 1050 Sprint GT.

 

 

 



£24.95
More info  

Cam Cover Ladder Seal (Spark Plug Tunnel) Set later 955 and all 1050 models.
( K924 )

Cam Cover Ladder Seal Set (Spark Plug Tunnel) later 955 and all 1050 models. x 3 seals in the set. Replaces Triumph T3600088

Fits: 955 ST and 955RS from VIN 139277,  Daytona 955 from VIN132513, Speed Triple 955 from VIN141872, 1050 Speed Triple, 1050 Speed Triple R, 1050 Speed Triple S, 1050 Tiger, Tiger Sport, 1050 Sprint ST and 1050 Sprint GT.



£10.95
More info  

Cam Cover Seal Set 955, T595, T509, 955 Daytona, Tiger 900 Injection
( K926 )

Cam cover seal set with x 8 cam cover screw seals to fit T509, Daytona T595, 955 Daytona (up to VIN 132512), Speed Triple 955 (up to VIN 1414871), Sprint ST 955 (up to VIN 139276), Sprint RS (up to VIN 139276), Tiger 900 (injection) and 955 Tiger.



£24.95
More info  

T595/T509/ early 955 model Daytona/Speed Triple grab rail
( L166 )

To fit T595 and early 955 Daytona/Speed Triple models with removable front panel on petrol tank and inlet holes in seat side panel.



Contact Us For Details

T595/T509 and 955 2002< Daytona/Speed Triple sports rack
( L167 )

Fits T595/955 models up to vin. number 132513 (Removable front panel on petrol tank and inlet holes on seat side panels). All racks now finished in black.



Contact Us For Details

Mirror to fit 600 Speed Four, 955 Tiger and 955 Speed Triple.
( M308 )

Replacement mirror oval convex 10mm threaded to fit 600 Speed Four, 900 Tiger (injection), 955 Tiger and 955 Speed Triple. Can be fitted left or right. Quantity x 1.

Will fit all models with 10 mm threaded mirror fixing size



£29.00
More info  

Mirror chrome to fit 900 Thunderbird, Thunderbird Sport and 955 Speed Triple
( M316 )

Replacement chrome mirror with convex lens to fit SE and Bonneville from vin 380777, Scrambler, Thruxton, 900 Thunderbird, Thunderbird Sport, Legend and very late 955 Speed Triple. This has a 10mm thread. Price for x 1 mirror. Fits left and right side.

Will fit all models with 10 mm threaded mirror fixing size



£39.00
More info  

Mirror base sleeve clamp and boot chrome. Thunderbird/Legend/Speed Triple
( M439 )

Chrome mirror base sleeve clamp and boot to fit original mirrors used on the 750/900 Speed Triple, Thunderbird 900, Thunderbird Sport, Legend, 955 Speed Triple. Thruxton, SE and Bonneville from VIN 380777 and Scrambler.  These also fit the oval mirrors used on the 900 Tiger EFI and 955 Tiger. Supplied as a pair.



£24.95
More info  

Bar end mirror, classic style black
( M690 )

 Bar end mirror to fit Thuxton.



£39.00
More info  

Bar end mirror, classic style chrome
( M691 )

Bar end mirror to fit Thruxton.



£29.95
More info  

Mirror clamp boot
( M878 )

Black rubber replacement for perished original covers. Used on most unfaired models.



£3.95
More info  

Replacement chromed fork tubes to fit most models
( S063 )

Replacement front fork tubes available for the models listed.  Internal tube components need swapping from original to replacement tubes which involves grinding the end of the original tube.. Triumph have used Kayaba and Showa as suppliers for forks. We stock seals and fork bushes. State model and vin number when ordering please. Popular models in stock, others to order. New fork bushes need fitting when fitting new tubes as the original bushes can get distorted taking the forks apart. Price per tube. Made in UK.





£99.00
More info  

Replacement chromed fork tubes to fit most models
( S064 )

Ready to fit original equipment quality front fork tubes, there is no grinding the end of the tube and having to swap internal valves. Triumph have used Kayaba and Showa as suppliers for forks. We stock seals and bushes for both Kayaba and Showa. New fork bushes need fitting when fitting new tubes as the original bushes can get distorted taking the forks apart. State model and vin number when ordering. Popular models in stock, others to order. Price per tube.





£135.95
More info  

Steering head bearing set.
( S306 )

Taper roller lower and ballrace upper bearing. To fit all 900/955 aluminium alloy framed models. Speed Triple, Daytona and Sprint RS/ST.



£27.00
More info  

Replacement fork seals (priced per pair)
( S503 )

45 mm fork seals to fit Showa forks. These were first used on the T595 Daytona and T509 Speed Triple. Also fit 955 Daytona and 955 Speed Triple. Now with double spring sealing.



£10.95
More info  

Replacement fork seals (priced per pair)
( S503 )

45 mm fork seals to fit Showa forks. These were first used on the T595 Daytona and T509 Speed Triple. Also fit 955 Daytona and 955 Speed Triple. Now with double spring sealing.



£10.95
More info  

Fork Dust Seals, 45mm Showa forks.
( S516 )

Dust seal to fit 45mm Daytona T595, Daytona 955, Speed Triple T509 and 955. Sold in pairs.



£12.95
More info  

Fork Bush Set, 45mm Showa.
( S619 )

Ptfe coated fork bush set to fit T595, T509, 955 Daytona and Speed Triple. Very similar to some Honda Fireblade forks, these use a 45mm tube and are supplied to Triumph by the Japanese Showa company. Apart from the way the front mudguard is retained (presumably to avoid fixing lugs and make the external machining easier), these are a good quality product.



£29.00
More info  

Drag link Bearings, Seals and hardened sleeve kit T595, 955 Daytona, 955 Speed Triple
( SD550 )

Drag link bearings, seals and the hardened sleeve for all single sided swinging arm models T595, 955 Daytona, T509, 955 Speed Triple, and 1050 Speed Triple up to VIN 461331. The drop link is a plated steel component.



£40.00
More info  

Drop Link Bearings, Seals and Hardened Sleeve kit to fit T595, 955 Daytona, 955 Speed triple
( SD554 )

Drop link bearings, seals and all hardened sleeves for T595, 955 Daytona, T509, 955 Speed Triple, 1050 Speed Triple up to VIN 461331. The drop link is the aluminium alloy part of the linkage.



£119.00
More info  

Swinging Arm Pivot Bearing Set 955 & 1050
( SD580 )

Swinging arm bearing and seal kit to fit all single sided swinging arm Daytona, Speed Triple and Sprint ST/RS models.

Fits: Daytona T595, Daytona 955 (single sided swinging arm), Speed Triple T509, 955 Speed Triple, 1050 Speed Triple & R, 955 Sprint RS, 955 Sprint ST, 1050 Sprint ST and 1050 Tiger Sport.



£29.95
More info  

Gear Change Shaft Oil Seal
( TA737 )

Outer oil seal on the gear change shaft on vitually all Triumph models. The existing seal can be very carefully hooked out and a new seal fitted. On models with a removable cover it's better to remove the cover to do the job. When fitting the seal back onto the splined gear shaft, it's good to cover the spline with tape to protect the seal inner.

Fits: TT600, Speed Four, 600/650 Daytona, 750/900 Trident, 900/1200 Trophy, 750/900/1000/1200 Daytona, 750/900 Speed Triple, Sprint 900, Sprint Sport, Sprint Executive, T509, 955/1050 Speed Triple, 955/1050 Sprint ST, 955 Sprint RS, Tiger 900/955/1050, Thunderbird 900, Thunderbird Sport, Adventurer, Legend TT.  Fits all the Bonneville range up to VIN 372312, Bonneville, T100, Thruxton, Scrambler, Speedmaster and America.



£4.30
More info  

Gearbox Output Shaft Seal. Replaces Triumph T3600112
( TA740 )

Gearbox output shaft HTC directional oil seal (anticlockwise for all these models - not suitable for the Bonneville engines as they use a clockwise directional seal) fits T509, T595, 955 Daytona, 955 Speed Triple, 1050 Speed Triple, 955 Sprint ST, 955 Sprint RS, 1050 Sprint ST, 750/900 Trident, 750/900 Speed Triple, 750/900/1000/1200 Daytona, 900/1200 Trophy, Tiger 900 (carburettor and injection), 955 Tiger, 1050 Tiger, Thunderbird, Thunderbird Sport, Adventuer, Legend, Trident Sport, Sprint 900, Sprint Sport and Sprint Executive.

Replaces Triumph T3600112     

 



£4.95
More info  

Oil Seal Valve Stem. Replaces Triumph 3600004-T0301
( TA745 )

Brown valve stem seal sold individually. 5.5 mm valve stem size. Fits Bonneville, SE, T100, Speedmaster, America, Scrambler, Thruxton, Rocket 3, Classic, Roadster, Touring, Adventurer, Thunderbird, Thunderbird Sport, Legend, 750/900 Trident, 750/900 Speed Triple, 750/900/1000/1200 Daytona, 900/1200 Trophy, 900 Sprint, Sprint Sport, Sprint Executive, T595, 955 Daytona (up to VIN 132512), T509, 955 Speed Triple (up to VIN 141871) , 955 Sprint ST and RS (up to VIN 139276), Thunderbird 1600/1700, Thunderbird Storm, LT, Tiger 900 (carb and EFI), 955 Tiger

Replaces Triumph 3600004-T0301

 

 

 

 



£3.95
More info  

Valve Stem Seal 5 mm (Green)
( TA746 )

Green valve stem seals sold individually. 5 mm valve stem size.

Fits 955 Sprint ST and RS from VIN 139277, Daytona 955 from VIN 132513, 955 Speed Triple from VIN 141872, 1050 Sprint ST and GT, 1050 Tiger, Tiger Sport, 1050 Speed Triple, 1050 Speed Triple R, Tiger Explorer and XC, Trophy 1215 and SE.



£2.95
More info  

Rotary Breather Seal
( TA860 )

Rotary breather seal located under the left side engine cover. Oil in the airbox, smoke from the exhaust and excessive oil consumption are signs that this seal needs changing. Fits carburettor Bonneville, T100, Thruxton, America, Speedmaster, Daytona 1000, Daytona 1200, Adventurer, Thunderbird, Thunderbird Sport and Legend. Also to fits Tiger 900 (EFI), Daytona T595, 955 Daytona up to VIN 132512, T509, 955 Speed Triple up to VIN 141871, 955 Sprint ST and RS up to VIN 139276.  Labyrinth type seal, size 14.5 x 28.4 x 6.5. This replaces Triumph T3600059



£14.95
More info  

Rotary Breather Seal
( TA861 )

Rotary breather seal to fit later style 955 engines, located under the left side front engine cover. Oil in the airbox, smoke from the exhaust and excessive oil consumption are signs that this seal needs changing. Fits 955 Tiger, Daytona 955 from VIN 132513, 955 Speed Triple from VIN141872, 955 Sprint ST from VIN 139277 and 955 Sprint RS from VIN 139277. Labyrinth type seal, size 18.4 x 32.5 x 7.0. This replaces Triumph T3600089



£14.95
More info  

Seal for cam cover screw (Black) twin lip
( TA864 )

Engine cam cover screw seals used on all models (see note on Bonneville air cooled range below). Known as Dowty or bonded seals. This latest version has x 2 lips on the inside of the seal. 

This seal fits all models Triumph have made and replaces Triumph T1260309

Fits the Bonneville air cooled range before VIN 456550. For Bonneville, T100, Thruxton, America and Speedmaster only after VIN  456550 see part number TA865.



£1.99
More info  

Rear Axle Cover Set All Single Sided Swinging Arm Models.
( Z059 )

Spindle End Cover Kit for single sided swinging arm Triumphs (2 Covers).  These precision CNC machined aluminium covers are manufactured in the UK and black anodized finished.  The kit completely covers the spindle nuts and any clips so that the rear end is completely tidied up.  Right side is 87 mm diameter and left side 66 mm. Easily fitted / removed in minutes.

Fits:  

Daytona T595 & Daytona 955 (Single Sided Swinging Arm)

Speed Triple T509

Speed Triple 955

Speed Triple 1050

Speed Triple 1050R

Sprint RS 955 (Single Sided Swinging Arm)

Sprint ST 955

Sprint ST 1050

Sprint GT

 

 

 



£39.95
More info  

Stick Ignition Coil later 955 and all 1050 models
( Z134 )

Replacement for the Denso ignition coil to fit all 955 Daytona from vin 132513, 955 Speed Triple from vin 141872, Sprint RS/ST 955 from vin139277, all 1050 Sprint ST, 1050 Speed Triple and 1050 Tiger.



£59.95
More info  

NGK DPR8EA-9 spark plug
( Z272 )

Original equipment NGK DPR8EA-9 spark plug for 900/955 Tiger, Bonneville 800/865, Scrambler, America, Speedmaster, Thruxton, 750/900/1000/1200 Daytona, 750/900 Trident,  750/900 Speed Triple, Thunderbird 900, Legend TT, Adventurer, Thunderbird Sport,  900/1200 Trophy,  955 Sprint RS/ST up to vin 139276, T509 Speed Triple, 955 Speed Triple up to vin 141871, T595 Daytona, 955 Daytona up to vin 132512



£3.50
More info  

NGK CR8EK and CR9EK spark plug
( Z276 )

Original equipment NGK CR8EK and CR9EK twin electrode spark plug to fit TT600, Speed Four, 600/650675 Daytona,  675 Street Triple, 675 Street Triple R, Tiger 800, Tiger 1050, Speed Triple 1050, 955 Speed Triple from vin 141872, Daytona 955 from vin 132513, Sprint RS/ST from vin139277





£8.99
More info  

NGK DPR9EA-9 Spark Plug
( Z293 )

Cooler running than the recommended standard 8 grade NGK spark plug. Better when the ambient temperature is very high or the engine has been modified with higher compression pistons. Engine may be slightly more difficult to start but run cooler.



£3.50
More info  

Front Brake Switch all models
( Z303 )

Original front brake switch made by Alps Electrical Co, Japan to fit all Nissin front brake master cylinders except only the radial brake models. 

Fits: Adventurer, America, Bonneville 800/865, T100, SE, Legend TT, Rocket III, Classic, Roadster, Touring, Scrambler, Speed Four, Speed Triple 750/900, Speed Triple T509, Speed Trilpe 955, Speed Triple 1050 up to VIN 461331,  Speedmaster, Sprint 900, Sprint Sport, Sprint Executive, Sprint St 955, Sprint RS, Sprint ST 1050, Sprint GT, Street Triple, Thruxton, Thunderbird 900, Thunderbird Sport, Thunderbird 1600/1700. Thunderbird Storm, Tiger 800, Tiger 800XC, Tiger 900, Tiger 955, Trident 750/900, Trophy 900/1200, TT600   



£11.95
More info  

Front Brake Switch all models
( Z303 )

Original front brake switch made by Alps Electrical Co, Japan to fit all Nissin front brake master cylinders except only the radial brake models. 

Fits: Adventurer, America, Bonneville 800/865, T100, SE, Legend TT, Rocket III, Classic, Roadster, Touring, Scrambler, Speed Four, Speed Triple 750/900, Speed Triple T509, Speed Trilpe 955, Speed Triple 1050 up to VIN 461331,  Speedmaster, Sprint 900, Sprint Sport, Sprint Executive, Sprint St 955, Sprint RS, Sprint ST 1050, Sprint GT, Street Triple, Thruxton, Thunderbird 900, Thunderbird Sport, Thunderbird 1600/1700. Thunderbird Storm, Tiger 800, Tiger 800XC, Tiger 900, Tiger 955, Trident 750/900, Trophy 900/1200, TT600   



£11.95
More info  

Front wheel spindle driver tool 17/19/22/24mm hex.
( Z323 )

3/8" sq. drive multi fit for many recessed hexagon front  wheel spindles such as the 19mm hex recess on the 955 Sprint ST/RS, 955 Daytona and Speed Triple 2002>. Fits 17, 19, 22 and 24 mm hex.recesses.



£14.95
More info  

Indicator/Flasher Relay 3 pin (Original and LED Indicators)
( Z421 )

Quality European manufactured replacement 3 pin/connector indicator relay to fit all models. Like the original units, it also has a hazard function for models with a switch fitted.

This unit is also excellent with most LED indicators. Unlike the original incandescent bulbs, LED lamps are polarity sensitive.

Fits:Adventurer, Thunderbird 900, Thunderbird Sport, Legend, TT600, Speed Four, 600/650 Daytona, 750/900 Trident, 750/900/1000/1200 Daytona, 750/900 Speed Triple, Trophy 900/1200, Sprint 900, Sprint Sport, Sprint Executive, T509, T595, 955 Speed Triple, 1050 Speed Triple (up to VIN 735336), 955 Daytona, Tiger 900 Carb and EFI, Tiger 955, Rocket III, Classic, Roadster, Sprint ST 955 and  Sprint RS. 

Fits all the Bonneville range carburettor models, Thruxton, T100, America, Speedmaster and Scrambler. Also fits EFI Bonneville range up to VIN 521668.



£11.95
More info  

Hella flasher relay
( Z422 )

Genuine Hella replacement indicator relay for original 10w bulbs. (A few export markets and the Thunderbird 900 range use 21w).

Fits:TT600, Speed Four, 600/650 Daytona, 750/900 Trident, 750/900/1000/1200 Daytona, 750/900 Speed Triple, Trophy 900/1200, Sprint 900, Sprint Sport, Sprint Executive, T509, T595, 955 Speed Triple, 1050 Speed Triple, 955 Daytona, Tiger 900 Carb and EFI, Tiger 955, Rocket III, Classic, Roadster, Sprint ST 955 and  Sprint RS. 

Fits all the Bonneville range carburettor models, Thruxton, T100, America, Speedmaster and Scrambler. Also fits EFI Bonneville range up to VIN 521668.

Made in Germany.



£19.95
More info  

Twin high/low beam relay kit
( Z428 )

For twin headlight bikes supplied with only one high and one low beam working, this relay kit will reinstate  both high and low beam to work as pairs on Sprint 955 ST, Sprint 955 RS, Tiger 955, Daytona 955, Speed Triple 955.  The 2 relays supplied are each 40A rated.



£12.00
More info  

Starter Solenoid
( Z431 )

Fits: 750/900 Trident, 750/900/1000/1200 Daytona, T595, 955 Daytona, T509, 955 Speed Triple, 900/1200 Trophy, 900 Sprint, Sprint Sport, Sprint Executive, 955 Sprint ST, 955 Sprint RS, Tiger 900, Tiger 955, Thunderbird 900, Thunderbird Sport, Legend, Adventurer, TT600, Speed Four, Daytona 600, Daytona 650, Bonneville 800/865, T100, Thruxton, Scrambler, America, Speedmaster,



£19.95
More info  

Cam chain tensioner spring
( Z585 )

Replacement cam chain tensioner spring. It is recommended that the spring is replaced if its length has reduced significantly below 73.7mm. This is a much more cost effective option than replacing the complete tensioner assembly. To change the spring, acces by removing the large central bolt. The tensioner does not have to be removed. Removing just the central bolt still allows the ratchet mechanism to retain the existing tension on the cam chain.

Fits: Adventurer, America, Bonneville, T100 & SE, Daytona 750, 900, 1000, 1200, Daytona T595, Daytona 955, Rocket III, Classic, Roadster & Touring, Legend, Scrambler, Speedmaster, 750 & 900 Speed Triple, Speed Triple T509, 955 Speed Triple, 1050 Speed Triple, Sprint 900, Sprint Sport, Sprint Executive, Sprint RS & ST 955, 1050 Sprint ST, Thruxton, Thunderbird 900, Thunderbird Sport,Tiger 900 (carburettor), Tiger 900 (injection), Tiger 955i, Tiger 1050, 750 & 900 Trident, Trophy 900 & 1200.

 



£12.95
More info  

Starter Motor Denso
( Z595 )

Denso starter motor ready to fit:

Adventurer, 750/900/1000/1200 Daytona, Daytona T595, 955 Daytona (up to VIN 132512), Legend TT, Speed Triple T509, 955 Speed Triple (up to VIN 141871), 900/1200 Trophy, 900 Sprint, Sprint Sport, Sprint Executive, 955 Sprint ST (up to VIN 139276), 955 Sprint RS (up to VIN 139276), Tiger 900, Tiger EFI, Thunderbird 900, Thunderbird Sport and 750/900 Trident.

 



£169.00
More info  

Denso starter motor brushes
( Z596 )

1 pair of brushes fitted into holder/back plate to fit  all Denso starter motors.

Triumph have used Denso starter motors with Taigene starter motors being used normally on a few Thunderbird 900, Legend and Thunderbird Sport. A label showing the manufacturer with the Triumph part number was originally fitted.

Fits: Adventurer, 750/900/1000/1200 Daytona, Daytona T595, 955 Daytona (up to VIN 132512), Legend TT, Speed Triple T509, 955 Speed Triple (up to VIN 141871), 900/1200 Trophy, 900 Sprint, Sprint Sport, Sprint Executive, 955 Sprint ST (up to VIN 139276), 955 Sprint RS (up to VIN 139276), Tiger 900, Tiger EFI, Thunderbird 900, Thunderbird Sport and 750/900 Trident.



£24.95
More info  

Rebuild kit Denso starter motor
( Z598 )

Complete kit to rebuild a Denso starter motor.

Fits:Adventurer, Daytona 750,900,1000,1200, Daytona T595, Daytona 955 up to VIN 132513, LegendTT, Speed Triple 750,900, Speed Triple T509, Speed Triple 955 up to VIN 141872, Sprint 955 RS, Sprint 955 ST, Thunderbird 900, Thunderbird Sport, Tiger 900 carburettor and EFI, Trident 750,900 and Trophy 900,1200.



£53.95
More info  

Starter motor brush and back plate set. Denso.
( Z650 )

Starter motor brush and back plate set. Denso.

TT600 and Speed Four up to VIN 171120

Daytona 955 from VIN 132513

Speed Triple 955 from VIN 141872

Sprint 955 ST and RS from VIN139277

Tiger 955

Sprint 1050 ST and GT

 

 



£24.95
More info  

Starter Motor Rebuild Kit TT600, 955 and 1050
( Z652 )

Starter motor rebuild kit

TT600 and Speed Four up to VIN 171120

Daytona 955 from VIN 132513

Speed Triple 955 from VIN 141872

Sprint 955 ST and RS from VIN139277

Tiger 955

Sprint 1050 ST and GT

 



£39.95
More info  

Cam Cover Seal Set of 8 (3 Cylinder Carburettor Engines)
( Z701 )

8 cam cover screw seals to fit all 3 cylinder carburettor models. These bonded seals were known originally as Dowty seals.

TA864 x 8



£14.95
More info  

Dust Seals Front Wheel
( Z740 )

First line of defence for your wheel bearings, outer 'dust' seals are actually oil seals. This pair of front wheel seals are used on all carburettor 3/4 cylinder  models as well as 955 Sprint ST/RS and 955 Daytona/Speed Triple with 6 hole fixing front discs. Supplied as a pair.



£7.80
More info  

Dust Seals Front Wheel
( Z744 )

Front Wheel dust seals to fit Daytona 955 from vin 1325513 and 955 Speed Triple from vin141872



£7.90
More info